athornt2

1998 Camaro - Turn Key NASA American Iron Race Car - $12,000

Engine/Cooling
-5.3L LM4 with 30k miles - Makes great oil pressure. 60 PSI at race temp
-ASA Cam
-LS6 Valve springs
-Shaner Ported throttle body
-BBK Longtube Headers
-BBK 2.5" Y-pipe into 3" Merge
-Dynomax Bullet Muffler Dumped/ Also have Borla XR-1
-Improved Engineering oil pan Baffle
-340 rwhp/340 rwtq
-Tuned by MTI Racing
-3 qt Accusump
-Earl's Oil Cooler with Carbon fiber shroud
-C&R Radiator
-Core support eliminated allowing the radiator to be angled forward - Vented out of the hood
-Custom tubular front bumper incorporating front breather setup
-Water temps run 180 during hot summer months
-Oil temps run 255 in hot summer months
-Canton Racing Remote Oil filter adapter
-Comp Cams 15w-50 Oil

Transmission
-Fresh Super T-10 w/ 2.43 first gear ratio
-Hurst Competition Plus Shifter
-Transmission Pump & Cooler
-7 1/4" V-Drive Quarter Master Clutch
-Quarter Master Aluminum Bellhousing
-Quarter Master Reverse mount starter
-Custom drive shaft from the Driveshaft Shop

Rear End
-10 Bolt
-Detroit Tru Track Differential
-3.23 gear
-Aluminim T/A Girdle

Suspension
-Front & Rear Coilovers
-SN Series Bilstien Shocks (freshly built)
-Hypercoil Springs
-Rear shocks mounted with heims/clevis and have been tied into the roll cage
-LG Lower A-Arms
-93 Boxed Upper Control Arms with Global West Del-A-Lum Bushings
-Strano Hollow 35mm front sway bar
-Stock rear sway bar; Also have hellwig adjustable rear bar
-UMI Boxed subframe connectors
-Adjustable rear lower control arms w/ heims
-Unbalanced Engineering lowering Panhard Bar brackets
-3 Link Rear - tied into roll cage
-Adjustable UMI Panhard Bar

Brakes
- 4 Piston Brembo Calipers
-Custom Brake brackets made by MTI Machine to allow 17" wheels
-2005 Subaru STI Brake rotors
-Custom fabricated brake cooling duct
-Raybestos ST47 Front Pads
-Stock Rear calipers
-Hawk HT10 Rear pads
-Wilwood Brake Bias adjuster
-ABS deleted

Safety/Interior
-6 Point Roll Cage - NASA approved
-Driver side Nascar door bars
-Schroth Hans 6pt Harnesses
-Floor mounted fire extinguisher
-Sparco Pro ADV Seat
-Carbon Fiber Dash from RCR Nationwide Team
-Autometer Tach, Oil Pressure, Oil Temp, Water Temp Gauges
-Midwest Chassis drive shaft safety loop

Aero
-Custom front Splitter mounted 3.5" off the ground
-COT Carbon Wing
-11 lb Carbon Fiber Hood
-Radiator shroud exit through hood

Extras
-1 extra set of OEM 17x9 ZR1s w/ Toyo RA1 tires
-BCM
-Upper Control Arms
-Lower A-Arms
-Shock Clevises
-160 Thermostat
-Throttle Body
-2 Rear brake calipers
-1 Rear brake rotor
-2 Front hubs
-10 Bolt Rear end housing
-Axle
-Auburn Differential
-GM Header Gaskets
-1 sets of LS1 heads



















http://classifieds.racerconnect.com/details.php?id=471

Hardrvin

Car weight? (curious relative to the power/weight)

Stock fuel tank setup?

athornt2

3300 with me and a full tank of fuel. I weigh 250 lbs. I also have a lexan window for the hatch. Yes, stock fuel tank. I ran a 1:36.2 at Road Atlanta in December on a set of 20 heat cycle RA1s. With a new set of RRs the car should easily break into the 34s.

AzMotorhead

Need a price in the ad please

athornt2

Added. Sorry about that.

rustyguns

That is quick! Very Nice Car! Look like a blast to drive!

athornt2

Thanks! It is definitely a blast to drive.

athornt2

Lowered price to $12,000. Feel free to make an offer. I need to sell this asap.

athornt2

Lowering again. $11,500. I need the money for another project.

Midnight89

Yikes -- nice times at Road Atlanta!

Nice turn key race car here.

athornt2

Thanks for the kind words. Lowering price 11,250 obo

athornt2

Lowering again. $10,900. There is no way you could build a car for this. The car is ready to go on track right now. I also have a Sparco passenger seat that can go with the car. Please pm me with any questions.