Where did the cryo rotor thread go?
#2
Team Owner
Looks like all of the threads that were posted in the Gen sections are gone too. Did he get upset and leave? Some of the posts seemed to bash him but there did seem to be some interest.
I had asked if they were going to be available for my 87.
I had asked if they were going to be available for my 87.
#3
Team Owner
Thread Starter
Probably got his money back and
#5
I did! Even thanksed him for his honesty. But, I think I was the last post in the thread before it went bye bye.
I dont think he was treated like a POS at all. Some of you guys in this forum reallly know your stuff and it shows.
So when some folks show up tryin to make a silk purse out of a sows ear, those that have been there done that, call
#7
Team Owner
Thread Starter
I did! Even thanksed him for his honesty. But, I think I was the last post in the thread before it went bye bye.
I dont think he was treated like a POS at all. Some of you guys in this forum reallly know your stuff and it shows.
So when some folks show up tryin to make a silk purse out of a sows ear, those that have been there done that, call
I dont think he was treated like a POS at all. Some of you guys in this forum reallly know your stuff and it shows.
So when some folks show up tryin to make a silk purse out of a sows ear, those that have been there done that, call
Last edited by John Shiels; 12-02-2007 at 12:11 PM.
#8
since 99 I have seen a bunch of to good to be true promises. He was questioned or even grilled but most post were looking for answers before we dump our money to their pockets. The other brake vendor seems to have not been heard from lately or I may just be missing them R_?
I went with the Centirc brand. They are the one peice blanks that Stop Tech uses. (Centric owns Stoptech)
The rotors are very well made and the finish is perfect. Dealer cost they are about 35.00 each, you will find them for about 50.00 each. More than the NAPA, but nice stuff.
Part numbers for future reference:
120.62059
120.62060
120.62061
120.62062
BTW, these are the numbers for the C5, true left and right. Dont use the C6 part numbers as you will just get all lefts.
#10
Drifting
Member Since: May 2006
Location: Youngstown Ohio
Posts: 1,544
Likes: 0
Received 0 Likes
on
0 Posts
It was unfortunate a new vendor jumped in a topic that there have been a dozen very informative threads on in the past month or so. Drilled rotors were pretty heavily and negatively discussed and claims of higher cost quality over tested relatively inexpensive rotors is met with skepticism. A good suggestion for a new vendors might be to take the time review past threads on like products to understand their potential market. If a vendor looks at what the common problems are and come up with a good solution it will sell.
I'm not a marketing expert...but I have stayed at a Holiday Inn Express..
I'm not a marketing expert...but I have stayed at a Holiday Inn Express..
#11
Team Owner
Thread Starter
My good suggestion to vendors is don't come here to try and pull the wool over are eyes with false promises.
#12
#13
Pro
Member Since: Dec 2004
Location: Rocky Mount North Carolina
Posts: 509
Likes: 0
Received 0 Likes
on
0 Posts
Gee you guys were really nice to a sponser, and just think...
This time of year is about peace on earth and goodwill to men.
Would hate to see you all being nasty to someone.
This time of year is about peace on earth and goodwill to men.
Would hate to see you all being nasty to someone.
#14
Team Owner
Thread Starter
#15
Team Owner
Member Since: Sep 2003
Location: Raleigh / Rolesville NC
Posts: 43,084
Likes: 0
Received 25 Likes
on
25 Posts
What were some of the first lessons in those Engineering Material Science classes about thermal properties of Iron ?
#17
#18
Advanced
Member Since: Jan 2007
Location: Greenwood Indiana
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
another one bites the dust
I wish the fella didn't just pack up and go home. Even if his rotors didn't last 3 times as long, at 50.00 each, for drilled and slotted, seemed fair enough to me. I would have probably given them a shot.
As accomplished and experienced as some of the forum members are on here, I would hope they realize there is a fine line between being knowledgeale and being rude. R. Ford
As accomplished and experienced as some of the forum members are on here, I would hope they realize there is a fine line between being knowledgeale and being rude. R. Ford
#19
Race Director
Did he leave or get kicked off?
#20
Melting Slicks
I think the final straw was him taughting HP plus pads for the track.
That was a total display of ZERO brake knowledge.
He was a hawk dealer too, and knew nothing of race pads. pretty sad.
That was a total display of ZERO brake knowledge.
He was a hawk dealer too, and knew nothing of race pads. pretty sad.