Anybody have a C6 Torque Tube laying around?
#1
Pro
Thread Starter
Anybody have a C6 Torque Tube laying around?
I would like to confirm the C6 manual torque tube length from the face of the small bellhousing face to the larger rear transmission face. Got one from eBay with no markings...just want to be sure. Thanks.
#2
Racer
Member Since: Feb 2010
Location: recently back to Fort Lauderdale Florida
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
Man wish i saw this earlier, got one for mine at the shop.
Wont be back homoe until Sunday night, if nobody got you the info by then I'll stop be and measure it....On my way to the Petit....
Wont be back homoe until Sunday night, if nobody got you the info by then I'll stop be and measure it....On my way to the Petit....
#3
Pro
Thread Starter
I would appreciate it....this tube is new...easy to tell that, but doesn't have the normal stock number sticker I normally see or springs near the trans bell section......
#8
Pro
Thread Starter
Looks like yours is 56" to my 55 7/8"....close enough for GM tolerances I am assuming....hehe
Thanks.
#9
Drifting
Member Since: Dec 2005
Location: Dayton, OH
Posts: 1,822
Likes: 0
Received 0 Likes
on
0 Posts
#10
Racer
Member Since: Feb 2010
Location: recently back to Fort Lauderdale Florida
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
62.5 inches complete with the engine bellhousing attached
From a c6 z06
Take off 6" for the bellhousing
From a c6 z06
Take off 6" for the bellhousing
Last edited by sspeed30043; 02-08-2012 at 06:13 PM.
#11
Pro
Thread Starter
HEHE...now you guys are contradicting one another....I LOVE BUILDING RACE CARS FROM SCRATCH WITH PARTS FROM ALL OVER THE PLACE....DOH
hehe....I guess I can believe it is OK with a grain of salt...will bolt them together with the bell and see what I get for the hell of it....
hehe....I guess I can believe it is OK with a grain of salt...will bolt them together with the bell and see what I get for the hell of it....
#12
Pro
Thread Starter
Ah...more mud to the mix.....When I attach the bell to the TT, the measurement is EXACTLY 62.5"!!!
But the bell is approx. 6.5" deep.
Go figure...hehe
But the bell is approx. 6.5" deep.
Go figure...hehe
#15
Pro
Thread Starter
OK...for future reference...if anyone needs this info
I bought another TT off of eBay because it was cheaper to get all the "guts" from the TT than buy them new from Chevy. Am replacing the driveshaft with a Driveshaft Shop one.
I got a Z06 from a 2006-7 car....part number 24236106 and it is the exact same length as the one I had....that is 55 7/8" from the bolt surfaces....the wide "bell" at the tranny to the narrow one that bolts to the bell housing. If you include the bell housing, it is 62 3/8" or 62 1/2".
FYI
I bought another TT off of eBay because it was cheaper to get all the "guts" from the TT than buy them new from Chevy. Am replacing the driveshaft with a Driveshaft Shop one.
I got a Z06 from a 2006-7 car....part number 24236106 and it is the exact same length as the one I had....that is 55 7/8" from the bolt surfaces....the wide "bell" at the tranny to the narrow one that bolts to the bell housing. If you include the bell housing, it is 62 3/8" or 62 1/2".
FYI
#16
Length of transmission
Hi
Can anyone help me with the overall length of the transmission from the centre line of the diff to the back face of the engine.
This is so I can see if a C6 transmission will fit in my Jaguar without lenghening or shortening it.
Thanks
Can anyone help me with the overall length of the transmission from the centre line of the diff to the back face of the engine.
This is so I can see if a C6 transmission will fit in my Jaguar without lenghening or shortening it.
Thanks