Installed Procar Rally seats
#1
Instructor
Thread Starter
Installed Procar Rally seats
I wanted a seat that was more form fitting for me, so I got the Procar Rally 1000 seats fit great and took about 2 hours to install with procar mounting bracket.
The following users liked this post:
DWD66VETTE (09-22-2016)
#3
Burning Brakes
Member Since: Jan 2002
Location: Redondo Beach CA
Posts: 1,200
Received 61 Likes
on
50 Posts
C2 of Year Finalist (performance mods) 2019
How is it getting in and out. Those side bolsters are pretty tall, and the Corvette steering wheel is big. I remember my buddy had those seats in his Camaro and it made it harder to get in and out. But our Corvettes are lower and have bigger steering wheels.
The following users liked this post:
DWD66VETTE (09-23-2016)
The following users liked this post:
DWD66VETTE (09-23-2016)
#6
Race Director
They look good and amazingly it seems like they fit well.
The following users liked this post:
DWD66VETTE (09-23-2016)
The following users liked this post:
DWD66VETTE (09-23-2016)
The following users liked this post:
DWD66VETTE (09-23-2016)
#9
Melting Slicks
Nice seats! Look 100% better than tall seats.
The following users liked this post:
DWD66VETTE (09-23-2016)
#10
Instructor
Thread Starter
I have a 14" wheel in my car. I'm not a very big person, only 5'-6" and 170 lb's, so I don't have any problem getting in and out.
#11
Instructor
Thread Starter
I used the ProCar bracket 81172 that mounts to the floor. The only thing I had to do was drill a hole in the top of my existing rear seat strap bracket.
I can go back to my original seats any time I want to. The whole process to switch back is about 20 minutes to do. Just 4 bolts per seat.
I can go back to my original seats any time I want to. The whole process to switch back is about 20 minutes to do. Just 4 bolts per seat.
Last edited by DWD66VETTE; 09-23-2016 at 11:19 AM.
The following users liked this post:
3JsVette (09-23-2016)
#12
Drifting
I used the ProCar bracket 81172 that mounts to the floor. The only thing I had to do was drill a hole in the top of my existing rear seat strap bracket.
I can go back to my original seats any time I want to. The whole process to switch that about 20 minutes to do. Just 4 bolts per seat.
I can go back to my original seats any time I want to. The whole process to switch that about 20 minutes to do. Just 4 bolts per seat.
#16
Burning Brakes
Member Since: Jan 2002
Location: Redondo Beach CA
Posts: 1,200
Received 61 Likes
on
50 Posts
C2 of Year Finalist (performance mods) 2019
SCAT is a few miles from me, and I've been there in person to check out seats. No cost savings, but I can buy right from them and bring them home if I want. Did that for my Chevelle, but had to make my own brackets since they did not make Chevelle adapters back then.
#17
Team Owner
Member Since: Nov 2005
Location: Beach & High Desert Southern California
Posts: 25,489
Received 2,339 Likes
on
890 Posts
I too have a smaller 14 inch wheel, with an ididit tilt column. In and out is not the drop and slide like with stock seats, but not too difficult (and once in they hug).
I chose the velour centers and headrests to minimize sun scorched seat burn on bare legs.
Nice.
The following users liked this post:
DWD66VETTE (09-23-2016)
#18
Racer
procar seats
I wanted a seat that was more form fitting for me, so I got the Procar Rally 1000 seats fit great and took about 2 hours to install with procar mounting bracket.
Attachment 48020738
Attachment 48020739
Attachment 48020740
Attachment 48020738
Attachment 48020739
Attachment 48020740
The following users liked this post:
DWD66VETTE (09-26-2016)
#19
Melting Slicks<br><img src="/forums/images/ranks/3k-4k.gif" border="0">
Member Since: Mar 2008
Location: Colorado Springs Colorado
Posts: 3,086
Received 1,946 Likes
on
704 Posts
2023 C2 of the Year Finalist - Unmodified
I really like the way these seats look. I've been looking to upgrade my original seats in my '66 convertible and these may be the ticket.
The following users liked this post:
DWD66VETTE (09-26-2016)