Mostly C1, Some C2 Parts For Sale
02-16-2004, 10:10 AM
#1
Melting Slicks
Thread Starter
Mostly C1, Some C2 Parts For Sale
For sale. Email cjr1@gte.net if you want any of this stuff. Make a reasonable offer. Sorry, no pictures. Buyer pays shipping from Boston.
“NIB” = new in box or new in the plastic baggy in which the vendor shipped it. In any case, “NIB” means a new and unused item.
1. 58-62 Corvette 3 5/8” generator pulley. All except FI and high lift cam. Excellent condition, ready to bolt on.
2. AC Delco rebuilt generator. AC Delco p/n 322-47. Chevy p/n 12321151. Replacement for 62 Corvette and many other Corvette and Chevrolet applications. NIB.
3. 56-58 Corvette hubcap. Dish is near perfect. Spinner has a few zits. With a new spinner, this would go on a Top Flight car.
5. 61-62 Corvette aluminum bell housing, cast 3779553. Also fits 61 Chevy with 348; 61-62 Chevy with 409; and, 62 Chevy with 300 HP 327. With 4 correct transmission mounting bolts and washers, 5 correct extension mounting bolts, 1 good clutch fork mounting ball stud, and 1 crummy boot. All threads in starter and other mounting holes are good. No helicoils and none needed. Some (correct) orange engine overspray, but mostly bare. Excellent condition. This could go onto a Flight car as is. Never blasted, beaded, welded, or modified. No cracks, or chips. Shipping may be expensive because I will take this to the UPS Store (ex-Mailboxes, Etc.) for packing.
6. 59-62 Corvette original appearing shifter shaft/handle. Bolts to Hurst shifter below the boot. Appears stock above the boot. Never used. Zip p/n ST-348. Corvette Central p/n 531102. No ball.
7. Hurst shifter shaft/handle with ball. 2 bolt design. Bolts to shifter. Stamped 7238.
9. 55-62 Corvette transmission to driveshaft yoke. Chevy p/n 3712379. The correct 5” long one for a T10 (16 spline – “coarse”).
10. 55-62 Corvette driveshaft with a 5” long transmission yoke to fit a 26 (“fine”) spline Muncie. 2 new installed U-joints. The 5” long yoke is rare and necessary for C1 Corvettes. Shipping may be expensive because I will take this to the UPS Store (ex-Mailboxes, Etc.) for packing.
11. 56-62 Corvette clutch fork. Spring needs to be replaced. New spring included.
12. 57-62 clutch fork push rod. 3739045. NOS. Light surface rust from sitting in my cellar for many years should clean right up.
13. (2) 57-62 clutch fork push rod swivels. Chevy p/n 3764588. NIB
14. 64-66 Corvette (except big block) clutch push rod. Chevy p/n 3844209. NOS. Still in Chevy shrink wrap.
15. 56-62 Corvette flywheel bolts and washers. Set of 6. NIB. Zip p/n BL-412.
17. 56-62 transmission to bell housing correct bolts and washers. Set of 4.
18. 62 Corvette transmission cross-member to frame shims. 3 (2 needed). Also necessary for 56-61 Corvettes with Muncie transmissions. Corvette Central p/n 531314.
19. 53-62 Corvette transmission rubber mount and retainer.
20. Spicer 5-3022X U-joint. NIB. This is the U-joint needed to attach a Muncie yoke to a C1 driveshaft.
21. 53-62 Corvette gas cap. Replacement. Zip p/n GT-314. NAPA p/n 703-1033. NIB.
22. AC R-22 (13 lb.) radiator cap. 64-67 Corvette? Very good condition.
23. 62 Corvette 340 HP intake manifold. Cast 3795397. Needs work.
24. (2) 70-82 small block Chevy and Corvette starter brace. Paragon p/n 6504. NIB.
25. 53-62 Corvette NOS front shock lower mount bracket.
26. 53-62 Corvette and 49-54 Chevy 2 upper outer pivot shafts with bushings, Moog K-133.
27. 53-62 Corvette and 49-54 Chevy 2 lower outer pivot shafts with bushings, Moog K-111.
28. 53-62 Corvette and 49-54 Chevy 3 upper inner pivot shafts with bushings, Moog K-131, 2 bushings have “GM” stamped on them.
29. 53-62 Corvette and 49-54 Chevy 1 lower inner pivot shafts with bushings, Master CK-1132.
30. 53-62 Corvette and 49-54 Chevy pivot shaft seal kit, Zip p/n SU-305.
31. 53-62 Corvette 2 front rubber sway bar bushings.
32. 62 Corvette 300 and 340 HP fuel line from pump to carb inlet. Includes filter and all fittings. Believe this to be a repro.
33. 64-65 Corvette rubber fuel line. Fuel filter to carb inlet. Comes with correct clamps and correct markings on fuel line. Paragon p/n 5016K. NIB.
34. 63 Corvette carburetor. 3460S, dated J2. 300 HP, Powerglide. Was running fine when removed a few years ago. Complete with fuel line from pump, including filter, distributor line, air leaner stud, and fittings on back for PCV line. Jetted 10% leaner than stock for Denver altitude. Excellent original used condition.
35. 64-65 Corvette carburetor. 3721SB. Dated 2J3. 300 HP, manual transmission. Also service replacement for all 62-65 AFBs. Has a green triangular tag attached that I can’t make out. Appears to be a Chevy part number tag. Maybe an original 64 Corvette carb. Has 8 mounting holes in base.
36. 60-62 Corvette air cleaner lid. No base. Used but decent element. Good condition, but some minor dings.
37. 66-72 Corvette, Camaro, and Chevelle open 14” air cleaner. Includes drop down base, new element, hose from base to valve cover, and lid. Original, not a repro. Lid chrome has blemishes.
[Modified by chris ritchie, 10:42 AM 2/17/2004]
“NIB” = new in box or new in the plastic baggy in which the vendor shipped it. In any case, “NIB” means a new and unused item.
1. 58-62 Corvette 3 5/8” generator pulley. All except FI and high lift cam. Excellent condition, ready to bolt on.
2. AC Delco rebuilt generator. AC Delco p/n 322-47. Chevy p/n 12321151. Replacement for 62 Corvette and many other Corvette and Chevrolet applications. NIB.
3. 56-58 Corvette hubcap. Dish is near perfect. Spinner has a few zits. With a new spinner, this would go on a Top Flight car.
5. 61-62 Corvette aluminum bell housing, cast 3779553. Also fits 61 Chevy with 348; 61-62 Chevy with 409; and, 62 Chevy with 300 HP 327. With 4 correct transmission mounting bolts and washers, 5 correct extension mounting bolts, 1 good clutch fork mounting ball stud, and 1 crummy boot. All threads in starter and other mounting holes are good. No helicoils and none needed. Some (correct) orange engine overspray, but mostly bare. Excellent condition. This could go onto a Flight car as is. Never blasted, beaded, welded, or modified. No cracks, or chips. Shipping may be expensive because I will take this to the UPS Store (ex-Mailboxes, Etc.) for packing.
6. 59-62 Corvette original appearing shifter shaft/handle. Bolts to Hurst shifter below the boot. Appears stock above the boot. Never used. Zip p/n ST-348. Corvette Central p/n 531102. No ball.
7. Hurst shifter shaft/handle with ball. 2 bolt design. Bolts to shifter. Stamped 7238.
9. 55-62 Corvette transmission to driveshaft yoke. Chevy p/n 3712379. The correct 5” long one for a T10 (16 spline – “coarse”).
10. 55-62 Corvette driveshaft with a 5” long transmission yoke to fit a 26 (“fine”) spline Muncie. 2 new installed U-joints. The 5” long yoke is rare and necessary for C1 Corvettes. Shipping may be expensive because I will take this to the UPS Store (ex-Mailboxes, Etc.) for packing.
11. 56-62 Corvette clutch fork. Spring needs to be replaced. New spring included.
12. 57-62 clutch fork push rod. 3739045. NOS. Light surface rust from sitting in my cellar for many years should clean right up.
13. (2) 57-62 clutch fork push rod swivels. Chevy p/n 3764588. NIB
14. 64-66 Corvette (except big block) clutch push rod. Chevy p/n 3844209. NOS. Still in Chevy shrink wrap.
15. 56-62 Corvette flywheel bolts and washers. Set of 6. NIB. Zip p/n BL-412.
17. 56-62 transmission to bell housing correct bolts and washers. Set of 4.
18. 62 Corvette transmission cross-member to frame shims. 3 (2 needed). Also necessary for 56-61 Corvettes with Muncie transmissions. Corvette Central p/n 531314.
19. 53-62 Corvette transmission rubber mount and retainer.
20. Spicer 5-3022X U-joint. NIB. This is the U-joint needed to attach a Muncie yoke to a C1 driveshaft.
21. 53-62 Corvette gas cap. Replacement. Zip p/n GT-314. NAPA p/n 703-1033. NIB.
22. AC R-22 (13 lb.) radiator cap. 64-67 Corvette? Very good condition.
23. 62 Corvette 340 HP intake manifold. Cast 3795397. Needs work.
24. (2) 70-82 small block Chevy and Corvette starter brace. Paragon p/n 6504. NIB.
25. 53-62 Corvette NOS front shock lower mount bracket.
26. 53-62 Corvette and 49-54 Chevy 2 upper outer pivot shafts with bushings, Moog K-133.
27. 53-62 Corvette and 49-54 Chevy 2 lower outer pivot shafts with bushings, Moog K-111.
28. 53-62 Corvette and 49-54 Chevy 3 upper inner pivot shafts with bushings, Moog K-131, 2 bushings have “GM” stamped on them.
29. 53-62 Corvette and 49-54 Chevy 1 lower inner pivot shafts with bushings, Master CK-1132.
30. 53-62 Corvette and 49-54 Chevy pivot shaft seal kit, Zip p/n SU-305.
31. 53-62 Corvette 2 front rubber sway bar bushings.
32. 62 Corvette 300 and 340 HP fuel line from pump to carb inlet. Includes filter and all fittings. Believe this to be a repro.
33. 64-65 Corvette rubber fuel line. Fuel filter to carb inlet. Comes with correct clamps and correct markings on fuel line. Paragon p/n 5016K. NIB.
34. 63 Corvette carburetor. 3460S, dated J2. 300 HP, Powerglide. Was running fine when removed a few years ago. Complete with fuel line from pump, including filter, distributor line, air leaner stud, and fittings on back for PCV line. Jetted 10% leaner than stock for Denver altitude. Excellent original used condition.
35. 64-65 Corvette carburetor. 3721SB. Dated 2J3. 300 HP, manual transmission. Also service replacement for all 62-65 AFBs. Has a green triangular tag attached that I can’t make out. Appears to be a Chevy part number tag. Maybe an original 64 Corvette carb. Has 8 mounting holes in base.
36. 60-62 Corvette air cleaner lid. No base. Used but decent element. Good condition, but some minor dings.
37. 66-72 Corvette, Camaro, and Chevelle open 14” air cleaner. Includes drop down base, new element, hose from base to valve cover, and lid. Original, not a repro. Lid chrome has blemishes.
[Modified by chris ritchie, 10:42 AM 2/17/2004]
02-16-2004, 08:39 PM
#3
Melting Slicks
Member Since: Jun 2001
Location: Chicago/Lake Geneva/Phoenix IL/WI/AZ
Posts: 3,139
Received 168 Likes
on
88 Posts
St. Jude Donor '06
Re: Mostly C1, Some C2 Parts For Sale (chris ritchie)
send pics and prices of item 4 hubcaps, looking for caps for my car trailer
TommyN
TommyN
