FS-GMPP Aluminum Vortec Fast Burn Heads, Cam, Lifters, Rockers, more... BRAND NEW
10-28-2011, 12:57 PM
#1
Safety Car
Thread Starter
FS-GMPP Aluminum Vortec Fast Burn Heads, Cam, Lifters, Rockers, more... BRAND NEW
SOLD!!!
I have the following absolutely BRAND NEW GM Performance Parts from a NEW ZZ383..
Package Deal All for $1700 plus shipping FIRM
Heads- GM part #12464298 (this number superseded #12367712, which is stamped on the heads) Fast Burn Vortec aluminum.
210cc Intake Ports
62cc Combustion Chambers
2.000'' Int/1.550'' Exh Valves
-This head is a bolt-on 30 hp increase when used on GM's ZZ4 crate engine (according to GMPP)
-Sells for $650 EACH new
$1000/pair
Cam- GM part #12370846
-This hydraulic roller design contains eccentric for mechanical fuel pump. The duration at .050" tappet lift (intake/exhaust) is 222/230; and maximum lift with 1.5:1 rocker ratio (intake/exhaust) is 509/528. Valve lash is zero/zero and lobe center line is 112 degrees
-Sells for $250-$270 new
$200
Lifters, Guides, Retainer, hardware- GM part #12371042
-Factory Roller Block Hydraulic Roller Lifter Kit- With 16 Lifters, 8 Tie Bars, Ties Bar Hold down Spring & Hardware
-This roller lifter kit is used on all late model V8 blocks 1986 and newer. These second design lifters are used in late model 350 HO engines and use a higher check ball spring preload. This kit includes 16 of 809-17120735 roller lifters, 8 of 809-12550002 valve lifter guides, one of 809-14101116 valve lifter guide retainers, 4 of 809-24501365 retainer bolts, and 4 of 809-120386 retainer washers. This kit plus pushrod kit 809-12371041 and a roller tappet design camshaft will convert your engine to a roller lifters engine.
-Sells for $220 new
$175
Rocker Set GM part #12370838
Rocker Arms, Stud Mount, Full Roller, Self-Aligning, 1.5 Ratio, Fits 3/8 in. Stud, Chevy,Small Block,Set of 16
-Sells for $350-$400 new
$275
Pushrods GM part # 10241740
1010 Steel Material, 5/16'' Diameter, 7.122'' Length. Heavy-duty .060'' wall, standard length. For use in 2nd design ZZ-series engines without guide plates
- Sell for around $10 new
$100 for full set
If anyone is SERIOUSLY interested in any or ALL of these components, please EMAIL me at rdphil@comcast.net or call 253-219-1908 for more info and pictures.
These are parts I removed from a NEW ZZ383 in order to install other aftermarket performance parts. The part numbers were taken directly off the ZZ383 spec sheet.
Prices are FIRM (and 20%-40% off retail prices!), especially on the heads. If I dont sell them they will go on my ZZ4 for the CJ7!
Package Deal All for $1700 plus shipping FIRM
All prices PLUS shipping.
Thanks, and I hope somebody on the forum can use this stuff!
I have the following absolutely BRAND NEW GM Performance Parts from a NEW ZZ383..
Package Deal All for $1700 plus shipping FIRM
Heads- GM part #12464298 (this number superseded #12367712, which is stamped on the heads) Fast Burn Vortec aluminum.
210cc Intake Ports
62cc Combustion Chambers
2.000'' Int/1.550'' Exh Valves
-This head is a bolt-on 30 hp increase when used on GM's ZZ4 crate engine (according to GMPP)
-Sells for $650 EACH new
$1000/pair
Cam- GM part #12370846
-This hydraulic roller design contains eccentric for mechanical fuel pump. The duration at .050" tappet lift (intake/exhaust) is 222/230; and maximum lift with 1.5:1 rocker ratio (intake/exhaust) is 509/528. Valve lash is zero/zero and lobe center line is 112 degrees
-Sells for $250-$270 new
$200
Lifters, Guides, Retainer, hardware- GM part #12371042
-Factory Roller Block Hydraulic Roller Lifter Kit- With 16 Lifters, 8 Tie Bars, Ties Bar Hold down Spring & Hardware
-This roller lifter kit is used on all late model V8 blocks 1986 and newer. These second design lifters are used in late model 350 HO engines and use a higher check ball spring preload. This kit includes 16 of 809-17120735 roller lifters, 8 of 809-12550002 valve lifter guides, one of 809-14101116 valve lifter guide retainers, 4 of 809-24501365 retainer bolts, and 4 of 809-120386 retainer washers. This kit plus pushrod kit 809-12371041 and a roller tappet design camshaft will convert your engine to a roller lifters engine.
-Sells for $220 new
$175
Rocker Set GM part #12370838
Rocker Arms, Stud Mount, Full Roller, Self-Aligning, 1.5 Ratio, Fits 3/8 in. Stud, Chevy,Small Block,Set of 16
-Sells for $350-$400 new
$275
Pushrods GM part # 10241740
1010 Steel Material, 5/16'' Diameter, 7.122'' Length. Heavy-duty .060'' wall, standard length. For use in 2nd design ZZ-series engines without guide plates
- Sell for around $10 new
$100 for full set
If anyone is SERIOUSLY interested in any or ALL of these components, please EMAIL me at rdphil@comcast.net or call 253-219-1908 for more info and pictures.
These are parts I removed from a NEW ZZ383 in order to install other aftermarket performance parts. The part numbers were taken directly off the ZZ383 spec sheet.
Prices are FIRM (and 20%-40% off retail prices!), especially on the heads. If I dont sell them they will go on my ZZ4 for the CJ7!
Package Deal All for $1700 plus shipping FIRM
All prices PLUS shipping.
Thanks, and I hope somebody on the forum can use this stuff!
Last edited by MakoShark72; 02-29-2012 at 09:05 PM. Reason: photos
10-30-2011, 03:47 AM
#3
Safety Car
Thread Starter
01-31-2012, 06:16 PM
#19
Burning Brakes
Have any pics of them? Im interested. Been looking for a set to replace my iron vortecs, my compression is a tad high and I think these are just what im looking for. sbc_builder82@yahoo.com
02-02-2012, 01:38 AM
#20
Burning Brakes
wish I had that kinda money right now. I would totally take it all off your hands. Best of luck with the sale!
if no one buys any of it, I can start buying a couple of pieces at the beginning of next month (march), then more on the 15th, then I'd have to save a bit until i could buy the heads. I'll commit to buying it all within the next couple of months if you are willing to hold it all and bear with me until it is all bought.
if no one buys any of it, I can start buying a couple of pieces at the beginning of next month (march), then more on the 15th, then I'd have to save a bit until i could buy the heads. I'll commit to buying it all within the next couple of months if you are willing to hold it all and bear with me until it is all bought.
Last edited by TurboStitchCW; 02-02-2012 at 01:46 AM.