'68 rolling chassis, body parts, interior parts for sale
08-18-2012, 12:25 PM
#1
Former Vendor
Thread Starter
'68 rolling chassis, body parts, interior parts for sale
Complete rolling chassis, 327 engine, turbo 400 automatic, can sell minus engine and/or trans.
Frame is straight and solid, but has had repairs done to rust areas.
Repairs are solid, but the welding "frass" was not ground down, so they look ugly.
Also have very clean coupe firewall back body. Can sell entire piece or part out pieces of windshield frame/birdcage. Fenders and taillight panel are undamaged original black glass (can remove panels as needed).
Have a lot of the interior (Gunmetal), wiring harnesses, dashes, gauges, a/c components (do not have the a/c wiper bezel or driver's side a/c ducting), tach and speedo, cables, braces, brackets, bumpers, mirrors, tail light housings and lenses, seat belt guides, nice forward console, auto with a/c shift plate, etc., etc.
Please see photos and pricing below.
Asking $2,150.00 OBO for above rolling chassis/engine/trans---will part out--lots of stuff here; small spindles and hubs, complete brake system, complete rear end assembly, complete front suspension, complete steering assembly, engine and trans (unknown condition), a/c components, and frame. Have clean Texas (non salvage) title that can go with this or with the body.
Interior, brackets, bumpers (not shown), '68 only headlight assemblies (not shown), wiring, a/c pieces/parts, etc.
'68 only door lock/latch mechanisms---$125.00 each
Have the push button assemblies and linkage also---$100.00 each
Complete power window regulators with motors and wiring harnesses---$175.00 per side
Have top dash $175.00 and right dash $100.00 (no photos now)
Have nice coupe door glass---$75.00 per side
Door shells. These have rusty frames but excellent skins. $75.00 each as is, or I will pull the skins to save weight/shipping, but will ask $100.00 per skin (labor charge). I do have some nice Vet. and coupe shells and complete doors from other '68's (ask on pricing for your needs)
Have several sets of '68 only t tops--$50.00 per side
Speedo and tach (dash is no good)----$50.00 per
Interior pieces:
SOLD---Big block hood in the background is an original LT1 piece that needs repair---$275.00---SOLD
SOLD---'58 body in background is for sale, as is it's rolling chassis with 519 engine and power-glide.--SOLD
Many more '68 pieces/parts available.
All items located near San Antonio, Texas 78070
Thank for looking,
George
geopar@gvtc.com
210 748 4693
Oops, for got to load the body photos---will add later.
Frame is straight and solid, but has had repairs done to rust areas.
Repairs are solid, but the welding "frass" was not ground down, so they look ugly.
Also have very clean coupe firewall back body. Can sell entire piece or part out pieces of windshield frame/birdcage. Fenders and taillight panel are undamaged original black glass (can remove panels as needed).
Have a lot of the interior (Gunmetal), wiring harnesses, dashes, gauges, a/c components (do not have the a/c wiper bezel or driver's side a/c ducting), tach and speedo, cables, braces, brackets, bumpers, mirrors, tail light housings and lenses, seat belt guides, nice forward console, auto with a/c shift plate, etc., etc.
Please see photos and pricing below.
Asking $2,150.00 OBO for above rolling chassis/engine/trans---will part out--lots of stuff here; small spindles and hubs, complete brake system, complete rear end assembly, complete front suspension, complete steering assembly, engine and trans (unknown condition), a/c components, and frame. Have clean Texas (non salvage) title that can go with this or with the body.
Interior, brackets, bumpers (not shown), '68 only headlight assemblies (not shown), wiring, a/c pieces/parts, etc.
'68 only door lock/latch mechanisms---$125.00 each
Have the push button assemblies and linkage also---$100.00 each
Complete power window regulators with motors and wiring harnesses---$175.00 per side
Have top dash $175.00 and right dash $100.00 (no photos now)
Have nice coupe door glass---$75.00 per side
Door shells. These have rusty frames but excellent skins. $75.00 each as is, or I will pull the skins to save weight/shipping, but will ask $100.00 per skin (labor charge). I do have some nice Vet. and coupe shells and complete doors from other '68's (ask on pricing for your needs)
Have several sets of '68 only t tops--$50.00 per side
Speedo and tach (dash is no good)----$50.00 per
Interior pieces:
SOLD---Big block hood in the background is an original LT1 piece that needs repair---$275.00---SOLD
SOLD---'58 body in background is for sale, as is it's rolling chassis with 519 engine and power-glide.--SOLD
Many more '68 pieces/parts available.
All items located near San Antonio, Texas 78070
Thank for looking,
George
geopar@gvtc.com
210 748 4693
Oops, for got to load the body photos---will add later.
Last edited by Corvettes by George; 03-26-2014 at 10:15 AM.
08-20-2012, 08:59 PM
#4
Safety Car
Hello George - is that forward console OEM or aftermarket repro??? any cracks/ breaks or missing pieces in the plastic frame Thanks. PM sent
Last edited by bkvette3; 08-20-2012 at 10:05 PM. Reason: spelling
10-23-2012, 11:15 AM
#11
Former Vendor
Thread Starter
11-06-2012, 05:29 PM
#18
Former Vendor
Thread Starter
Sure.
'68 has no hole for the "pin" found on the '69 doors, and the fender trim pieces are a different length.
Send an e mail for photos.
geopar@gvtc.com
'68 has no hole for the "pin" found on the '69 doors, and the fender trim pieces are a different length.
Send an e mail for photos.
geopar@gvtc.com