1.6 Roller rockers Excellent shape....
10-12-2014, 04:15 PM
#1
Le Mans Master
Thread Starter
1.6 Roller rockers Excellent shape....
Sold...I just removed these 1.6 Yella Terra 7/16" stud aluminum roller rockers from my 383 motor..They have 22,000 miles on them and they're as tight as when new...Both the fulcrum and tip move smoothly...Yella Terras are made in Australia and are the elite roller rocker in that country for racing and street...I had these installed when my motor was built and have since changed over to the Crane Golds because they have the offset rockers to fit my Dart heads...My engine builder says these rockers cost him somewhere around "$270.00-$280.00" four years ago, they were in the middle range for this type rocker, so price and quality wise they're around the same as the Scorpion racing rockers..Also included are the Poly Lock fasteners, so you won't need to buy those....Im selling them for $130.00 which (includes shipping).. Shipping is going to cost me around $20.00 because these weigh around 8-9 lbs with the polylocks...WW (Paypal prefered)
Last edited by WW7; 11-16-2014 at 07:33 AM.
10-14-2014, 08:24 PM
#2
Intermediate
Member Since: Apr 2011
Location: Modesto Ca
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
Rockers for sale
Hello
I have a stock 96 lt4 vette with 98k and been wanting to replace the original crane self aligning rockers
Would I need guide plates ?
Will your studs screw into my heads?
Sounds like you have the deal I've been looking for
Thanks
Steve
I have a stock 96 lt4 vette with 98k and been wanting to replace the original crane self aligning rockers
Would I need guide plates ?
Will your studs screw into my heads?
Sounds like you have the deal I've been looking for
Thanks
Steve
I just removed these 1.6 Yella Terra 7/16" stud aluminum roller rockers from my 383 motor..They have 22,000 miles on them and they're as tight as when new...Both the fulcrum and tip move smoothly...Yella Terras are made in Australia and are the elite roller rocker in that country for racing and street...I had these installed when my motor was built and have since changed over to the Crane Golds because they have the offset rockers to fit my Dart heads...My engine builder says these rockers cost him somewhere around "$270.00-$280.00" four years ago, they were in the middle range for this type rocker, so price and quality wise they're around the same as the Scorpion racing rockers..Also included are the Poly Lock fasteners, so you won't need to buy those....Im selling them for $130.00 which (includes shipping).. Shipping is going to cost me around $20.00 because these weigh around 8-9 lbs with the polylocks...WW (Paypal prefered)
10-14-2014, 09:03 PM
#3
Le Mans Master
Thread Starter
I have no studs for sale, just rockers and polylocks....These rockers fit a 7/16" stud,and are 1.6 ratio.I"m not sure if the LT4 has 3/8" or 7/16" studs, or if your studs are pressed into the head or screwed into the head...If your not sure what configuration your heads are, ask on the Tech Forum and the guys on there will let you know what you have.....WW
Last edited by WW7; 10-15-2014 at 05:46 AM.
10-29-2014, 10:35 AM
#4
Le Mans Master
Thread Starter
ttt
10-29-2014, 12:27 PM
#5
Team Owner
Member Since: Oct 2004
Location: altered state
Posts: 81,242
Received 3,043 Likes
on
2,602 Posts
St. Jude Donor '05
LTx 10mm I think?
Bump for a solid seller
Bump for a solid seller