Parting out 88 Vert
#1
Instructor
Thread Starter
Parting out 88 Vert
Here is what's left of a car I bought for the engine/trans/misc. parts. First off, If anyone wants the whole thing it's $300, you haul. The car was repainted so any painted parts have tape lines and need painted to be nice. For parts:
Doors each with glass/motors/wiring/heated mirrors/ $75
Whats left of front susp. each side $100
Rear suspension each side $150 or $250 for the whole thing.
Hood $100
Convert rear deck lid $75
Lower Fenders each $35
I know there are a lot of other parts here, I'm so busy so please just ask and I can send pics and prices.
Prices do not include shipping and I can't ship big items like the hood etc.
Car is kept covered and did not get wet inside or under hood.
Doors each with glass/motors/wiring/heated mirrors/ $75
Whats left of front susp. each side $100
Rear suspension each side $150 or $250 for the whole thing.
Hood $100
Convert rear deck lid $75
Lower Fenders each $35
I know there are a lot of other parts here, I'm so busy so please just ask and I can send pics and prices.
Prices do not include shipping and I can't ship big items like the hood etc.
Car is kept covered and did not get wet inside or under hood.
#3
Parting out 88 Vert
Looking for Instrument panel & bezel/face plate.
Looking for center console lid assy.
Looking for left door window sweeps.
Looking for front three piece air dam.
Looking for rear corvette emblem (between tail lites)
Looking for both Hood gas supports (short & long)
Possibly front and rear emblems
pm sent
payment sent
Looking for center console lid assy.
Looking for left door window sweeps.
Looking for front three piece air dam.
Looking for rear corvette emblem (between tail lites)
Looking for both Hood gas supports (short & long)
Possibly front and rear emblems
pm sent
payment sent
Last edited by 88vetteL98; 01-02-2016 at 06:42 AM. Reason: payment sent
#4
Instructor
Thread Starter
Front and gas lid emblems. I would say the front is excellent. Has some wax to be cleaned out. The gas door emblem has some fine scratches over the bowtie and a few small chips at the bottom of the ring. Easy touch up.
I tried to get close for the pics.
I tried to get close for the pics.
Looking for Instrument panel & bezel/face plate.
Looking for center console lid assy.
Looking for left door window sweeps.
Looking for front three piece air dam.
Looking for rear corvette emblem (between tail lites)
Looking for both Hood gas supports (short & long)
Possibly front and rear emblems
pm sent
Looking for center console lid assy.
Looking for left door window sweeps.
Looking for front three piece air dam.
Looking for rear corvette emblem (between tail lites)
Looking for both Hood gas supports (short & long)
Possibly front and rear emblems
pm sent
#5
Instructor
Thread Starter
Picture of the shifter console. I thought this piece was messed up but after removing and doing a quick clean up it looks pretty good. The biggest issue is going to be some glue above the shift indicator. I tried to chip it off with my fingernail with no luck so that is for the buyer now. However, the graphics are great as well as the boot. Note only broken part is on the back where a screw goes in.
Last edited by GotMe1; 01-01-2016 at 10:35 AM.
#7
Parting Out 88
How much for the radio pig-tail with 4" of lead? Shipped to 78634. TIA
#9
Instructor
Thread Starter
#13
Instructor
Thread Starter
#15
Instructor
Thread Starter
I have that. It is on ebay right now for $148. I can do $135 in here including shipping.
http://www.ebay.com/itm/191771761267...84.m1555.l2649
http://www.ebay.com/itm/191771761267...84.m1555.l2649
Last edited by GotMe1; 01-03-2016 at 04:20 PM.
#16