The Official Chevrolet Corvette ZR-1 Picture Thread
#261
Race Director
The only rub issue was a very small part of the right rear liner that was trimmed down. I wanted a 12 on the rear but I couldn't get a figment guarantee from HRE so I went as wide as was suggested even though I knew a 12 would work,there's a few ZR-1s with a 13 on the rear. I don't have any build,repair threads other than the starter relay mod at the top of the page.
#262
Melting Slicks
I had to trim a little off the inner fender liner on both rears for my 12's to fit. My rears are 345/30/19's. Only a small trim on the left rear and a little more on the right, but still not much. Lots more options for tires with the bigger rims. Makes these ole Vettes look much better too!
#263
Race Director
That's true. I didn't want a 19 inch rear wheel but not too many tire options for 18 inch wheels. I do wish I would have gone with a slightly taller tire on the18 inch front wheel. I might do that at some point. While cleaning up the car a few weeks ago I did find one area where the tire skimmed the wheel well liner.
Last edited by Z51JEFF; 12-03-2016 at 08:21 PM.
#264
Drifting
I had to trim a little off the inner fender liner on both rears for my 12's to fit. My rears are 345/30/19's. Only a small trim on the left rear and a little more on the right, but still not much. Lots more options for tires with the bigger rims. Makes these ole Vettes look much better too!
The following users liked this post:
JimZRyd (12-04-2016)
#265
The only rub issue was a very small part of the right rear liner that was trimmed down. I wanted a 12 on the rear but I couldn't get a figment guarantee from HRE so I went as wide as was suggested even though I knew a 12 would work,there's a few ZR-1s with a 13 on the rear. I don't have any build,repair threads other than the starter relay mod at the top of the page.
I had to trim a little off the inner fender liner on both rears for my 12's to fit. My rears are 345/30/19's. Only a small trim on the left rear and a little more on the right, but still not much. Lots more options for tires with the bigger rims. Makes these ole Vettes look much better too!
#266
Melting Slicks
Jim
#267
Race Director
#268
Thanks! I would have to look back at my paperwork to get the offsets. These are the Profil 5's that Fikse makes. They remove a little more mass than on the FM5's so they are lighter. I'm running 18's on the front with a 285/35 PSS. I felt going 19's up front would force me to run a tire with too small a sidewall. Not a fan of the "rubber band" look. The specs for my set up are 18x10 up front with 285/35's and 19x12 out back with 345/30's.
Jim
Jim
Jeff,
No problem whoring such a lovely car.
Though I do feel it deserves a slightly better camera.
When one has the 18s and 19s next to the other, it becomes quite visible how the extra inch affect the spoke design. The rears look a bit sleeker than the fronts with the added spoke length.
#269
Melting Slicks
Jim
#270
Race Director
I had to trim a little off the inner fender liner on both rears for my 12's to fit. My rears are 345/30/19's. Only a small trim on the left rear and a little more on the right, but still not much. Lots more options for tires with the bigger rims. Makes these ole Vettes look much better too!
Jim I do like that 285 on the front. If it wasn't such a hassle I'd look into a set for my car. The wheel on my car is exactly as stock with the exception of the 1/2 inch added to the inside barrel of the wheel. FIKSE was one of my choices but they build them the way I wanted so I was met with the HREs. Don't want to come off like a picture ***** but I do have a lot of pictures of the car. Mike Gill has got 19s on his 94 and it looks HOT. As stated I didn't want to go with 19s on the rear but there are very few sizes for a 18-11.5 wheel. A 335 I think is available but didn't want that big.
The following users liked this post:
1993C4LT1 (01-14-2017)
#274
Intermediate
91 zr1
MODS INCLUDE:
Flowmaster Stainless Steel Long Tube Headers
Flowmaster True Dual Exhausts
Flowmaster Super 44 Mufflers
K&N Cold Air Lower Intake
ZR1 Specialist Performance Chip
61K
Flowmaster Stainless Steel Long Tube Headers
Flowmaster True Dual Exhausts
Flowmaster Super 44 Mufflers
K&N Cold Air Lower Intake
ZR1 Specialist Performance Chip
61K
Last edited by TealZR1; 04-05-2017 at 07:56 PM.
#275
Le Mans Master
Member Since: Jan 2000
Location: Georgetown TX
Posts: 8,424
Received 1,864 Likes
on
1,081 Posts
C5 of Year Finalist (appearance mods) 2019
duplicate post
Last edited by USAZR1; 06-20-2018 at 12:40 AM.
#276
Racer
I ran across a group of cars heading to a US car show last weekend, so I tagged along. The show was just north of Munich. I need to spend some time and clean the engine!
Last edited by KGV; 05-27-2017 at 03:44 AM.
The following users liked this post:
G-Sting (05-30-2017)