NAZTY Z

Up for sale is my 2002 Millenium Yellow ZO6 corvette. this car is an attention getter. car is very fast and loaded, never driven in the winter and very clean. well maitained just had its oil change mobil 1 synthetic. this is a true show and go car with around 25k in extra parts and labor factory options include heads up display, cruise, power windows and locks and seats, tilt wheel, bose radio, car has no rock chips in the front end like a lot of the corvettes you'll find. 50k miles car has a brand new clutch just installed last summer to handle the extra power it makes. brand new Nitto invo tires all the way around, performance engine parts have about 5000k miles on them since install, built rear end about 2000 miles done mid last summer. list of mods below

Exterior

Haltech tunnel ram
MCM carbon fiber high rise heat extractor hood
ACI front splitter
ACI side skirts
ZO6 mesh grill inserts side, rear and front vents
Ronal modular wheels
Band new Nitto Invo tires
Tinted windows
Black painted lower rear fascia
Black outs on front markers side markers and rear tail lights
Lowered 2 inches
Real 4300kl HID fog lights and head lights
Stainless steel dress up screw kit doors under hood and trunk
Carbon fiber under hood dress up kit
Custom flame Painted fuel rail covers and radiator shroud
Two color fender stripes

Interior

Full Vette Essentials leather interior seats are upgraded to the sport seats
Leather is black with yellow and black carbon fiber leather accents very tastefull
Up graded leather includes shifter boot and ****, E brake handle, and boot door pulls,
seats, arm rests, steering wheel and center arm rest
aluminum gauge bezels
led map lights
5 point harnesses
Harness bar with camera mount
Custom embroidered trunk liner with corvette logo

Engine and drivetrain

Custom grind comp cam
Ported oil pump
C5r timing chain and gear set
LS7 throttle body
Fast 90 intake
Carbon fiber power air bridge
Power coupler
SLP Blackwing cold air intake
Long tube coated headers
Borla cat back exhaust
Corsa off road X pipe
Brand new LS7 clutch
Built rear end
Hardened output shafts
4.10 gear
Custom dyno tune
QTP electric exhaust cut outs
short throw shifter

I'm sure there are probably a few things I am missing but you get the point

25,900 or best offer i am not on the forum as much with my work and a 2 year old on my hands ( he is the reason i need to sell it because I don't get to take it out much anymore)but i will check daily also feel free to email as well dalemilliken@quickenloans.com

NAZTY Z

Ttt

NAZTY Z

ttt

picklz

Nice looking ride, Sent you an email.

NAZTY Z

Thanks I just seen your email sending you some more pics

ezrider4u2

Very nice ride, question regarding the front plate insert, I noticed the mesh- do you have an oil cooler installed or is that to match the other inserts? I'm not sure if Michigan has a front plate requirement or not so I thought I'd ask and if not- do you have the regular front plate insert?

meadowz06

RWHP? Interested.

Spartan 45

PM and E-mail sent

NAZTY Z

we do not have a front plate requirement here in michigan and i have just the original corvette plate cover that went there. I did the mesh insert to and cut the bumper to allow the cold air to go straight to the blackwing air filter behind it.

NAZTY Z

last dyno was 420 RWHP on a conservitive dyno and before the exhaust was finished up on it.

NAZTY Z

Replied to your Email

NAZTY Z

ttt

PSC 02 Vette

You mentioned LED Map Lights in your list of interior mods. Was yours a single bulb installation that replaced a single bulb? The reason I ask is because my stock map lights are 9 bulb LEDs on a printed circuit board that emit a yellowish color. I would like them to emit a bright white color but I haven't found a replacement for this circuit board. Can you shed any light on my situation?
Thanks,