ocgearhead

Well its finally come time to part ways with my Z. I've owned it for 4 years and have only put 5,000 miles on it in that time. I just don't have the time to enjoy it like i truly should and want to move into some thing i will use more. The car currently has 77k on the body and roughly 16k on the engine and drive-train. no expense was spared when this car was built by the previous owner. very solid running car that will not disappoint. this setup should make 525rwhp the dyno

MOTOR MODS:

TachItUp Motorsports built- aluminum block LS2 with Eagle crank, Scat rods with ARP 2000 bolts, ARP main stud kit, and Wiseco custom pistons
Morel lifters
TEA Stage 2.5 LS6 heads… 58.75CC and 227cc runner
Custom Grind Comp cam 237/242 603/609 113lsa
Cometic .040 gaskets
Manton 3pc Heavy Duty pushrods (7.325)
Ported Fast 90 intake
Nick Williams 90mm throttle body
K&N Air Intake CIA System
SVO 42lb injectors
Single roller timing chain
ARP cam/ retainer plate bolts
ARP Head stud kit
ARP intake manifold bolts
ARP waterpump bolts
Meziere Electric water pump w/ 180 deg stat
Powerbond underdrive pulley
Map Sensor Relocation
Melling Oil Pump
Oil Catch Can

Exhaust:
LG Motorsports long tubes with no cats
borla strait pipes - very loud exhaust

Drivetrain:

Centerforce clutch
Centerforce flywheel
B&M ripper shifter with custom billet ZO6 ****
RPM Stage 5 MM12 tranny with hardened main shaft
DTE Stage 2 rear diff with 3.90 gears
DTE tranny/rear brace

Suspension:

Hal QA1 12 way adjustable shocks
Swaybar links Upgraded newer metal 02+
Hawk brake pads
Dimpled/slotted rotors

Exterior Appearance:

Custom billet fender badges
Carbon fiber rear brake duct covers
Clear turn signal lights
Stainless front and rear corvette enlays
LED tail lights
Stainless 8” shorty antenna

Interior:

Custom interior painted by C5 Kidd
Two tone leather goods
Dynojet Wideband commander mounted in ash tray (Doesn't seem to be working, but can be easily fixed)
Crazy Cowboy insulation kit
LLOYD ZO6 floor mats
Partition with custom billet ZO6 badge
Billet corvette door sills
Highs replaced with Infinity Kappa speakers
GM MP3 iSimple- w/ GMH20T connector
Custom Z06 Top Trunk Liner Cover
AEM Oil Pressure Digital and Analog gauge with 2 gauge pod (Have other basic filler gauge in just for aesthetic reasons. Gauge of choice can be added)

Wheels and Tires:
Replica C6 deep lip wheels professionally painted a matte bronze
18x10.5 rear with 325/40R18 M&H Racemaster drag radials - roughly 1,100 miles on them
17x9.5 front with sumitomo htr z 275/45R17 with the same milage


Cons to the car :

- the car will need the Rear diff rebuild fairly soon, it does have a decent whine to it. no issues driving it what so ever just being upfront with the issue. It had a very faint whine when i purchased it and it gradually grew worse. I talked with Rick from RKT on here and he would be the guy i would plan to send it to this winter if the car doesn't sell, sounds like a great guy and reasonable prices.

- the driver side auto tinting mirror has water in it and separated as seen in the picture below. very common issue on these cars, just never got around to fixing it because it didn't bother me while driving.

asking 21k firm, i feel that is a fair price for a car with the long list of tasteful mods and being 1 of 352 speedway white Z06's . located in Milwaukee county, Wisconsin

any questions or want more detailed pictures feel free to contact me on here or through a pm.

FX VETTE

Nice Z06, GLWS!

ocgearhead

bump

ocgearhead

really... no one? clean car tastefully modded. fully built stroker with quality parts throughout. will try and upload an idle video tomorrow. open to offers.

SlingShotYellow

Is the drivers seat broke or lose? looks like its leaning on the left side in the pic towards the left.. got the gangsta lean going..LOL...

There is a known problem with the drivers seats mainly on the Z's

probably best to take more pics or a video of the entire interior also showing seats, carpet and dash

So complete engine built? bottom to top? new pistons and all?

thanks

ocgearhead

Cold start up this morning

ocgearhead

No the seat is not broken, if it was i would have said so in the post. If you wanted any pictures in particular I specifically say feel free to ask. The interior is in great condition and has been well taken care of. It is not the easiest car to get decent pictures of the interior. You can see much of the interior from the pictures i posted. it has lloyd mats that are in great condition, not much to see. If you read the build list you can answer your own questions about the engine being built.

SlingShotYellow

Thank you for the answers. gets frustrating trying to get all details when so far away.

I will PM you with any other questions from now on.

I meant to add with not building an engine since i was 20 its been a long time so i didn't catch everything like new piston brand names rather than what we used as kids building motors. so out of practice on engine builds.

Once again thank you sir!

ocgearhead

I apologize for being alittle short with my answer. just been dealing with a bunch of tire kickers locally and its getting old fast. that and working 60+ hours this past week, I'm running on little sleep. id be happy to get you what you want to see, just let me know what you want through a pm.

ocgearhead

Interested party, pending funds. might be sold soon.

ocgearhead

car is sold