Originally Posted by 383 Z06

Any interior pics?

Originally Posted by Z06WHO

The car has 63,xxx miles on it and probably wont go up much with winter right around the corner. Always garage kept under the WCC car cover. The paint for the age is good, but it does has some flaws. Mainly on front bumper and by the rear brake duck vents from rocks being kicked up. No check engine lights. It was dyno tuned and made 505whp and 440wtq on LSXkiller mustang dyno in Bonner Springs, KS. II built the car to grip and look good.

Asking 27k fairly firm at that. But make offer the worst I can say is no thanks. (There's still a small loan on it threw Penfed).

You will not drive this car unless cash is in hand. No tire kickers or joyriders!!!!!

Engine/Drivetrain Modifications:
-TSP MS4 Cam
-PRC 227 Heads milled to 60cc*(installed by RPM)
-PAC Dual Valve Springs .660" (Installed 600 miles ago)
" " .675"*
-TSP Chromoly Pushrods 7.400"
" " 7.500"*
-LS7 Lifters*
-LS2 Timing Chain
-LS6 Timing Chain Dampener
-Hinson Short Enigine Mounts and Trans mount
-Vararam VR-B2 w/ duct
-B&B PRT exhaust
-MSD Spark Plug Wires
-SLP Underdrive Pulley
-SLP 160* Thermostat
-LG Super Pro Headers 1 7/8"; (catless)
-NGK TR-55 Plugs
-MSD 2 step Launch Control
-Monster Stage 3 clutch w/ billet with light weight flywheel
-MGW Short shifter (Latest version with the new lower shifter box)
-Tick performance clutch master cylinder
-Ls2 water pump
-FAST 102 LSX-R ported by Vengeance Racing*
-Nick Williams 102mm TB*
-FAST Billet Fuel Rails & 60lbs injectors*
-Elite Engineering Oil catch can
-WCC Underhood Carbon fiber cover kit
-Rebuilt Transmission (Oaks Auto Dealership had it rebuilt before I got the car) has roughly 7-8k miles sense rebuild I believe.

Suspension/Brake Modifications:
-QA1 Single Adjustable Coilovers 550lbs springs on all 4 (comes with a extra set of 350lbs springs for the front)
-C6 Z06 Brakes on all 4 corners
-Hawk HP+ ceramic puck pads
-Goodrich SS Lines

Wheels/Tires Modifications:
-360 Forged Mesh 8 (The Face of all the wheels are Hydrodipped carbon fiber)
-19x10 Front with 265/35/19
-20x13 Rears with 345/30/20
-Michelin Pilot Sport Cup 2 tires with about 1200 miles on them
-2 extra 305/30/20 Michelin Pilot Sport Cup 2 tires (roughly 1k miles)
-2 extra 1.5" 360 Forged wheel lips

Exterior Modifications:
-Matte Black GS Stripes
-Tint 35%, 20% Back Glass (Windows have some wear)
-Shorty Antenna
-Depo black turn signal housings
-Corvette Creation Carbon vortex lip (Cracked in the center. Not my fault, was like it when I bought the car)
-Corvette Creation ZR2 duraflex hood (Has a small crack in it by a vent)
-Corvette Creation AC Edition Carbon Fiber Side skirts
-Corvette Creation Carbon fiber Diffuser
-Corvette Creation carbon fiber Widebody fenders
-SLP lip spoiler (Properly repainted to color match)
-RPI Design "Corvette" rear bumper carbon fiber lettering
-Corvetteenvy Halo Taillights with hyperflash harness (lightly tinted)
-Side exit exhaust 3.5" tip
-Quarter-Max 4" carbon fiber exhaust ring
-Custom made Jake Skull exhaust enhancer plate
-C6Z Splash guards rear
-C6 Front Splash guards

Interior Modifications:
-Corbeau Evolution X Seats with red stitching. Also has sliding mounts
-Isimple iPod Interface (Converted over to work with Android phones)
-New black with red stitching shift boot (Will come with original one)
-Trunk partition
-Vette Tray with 2 cup holders and 2 cubby trays
-RPI Designs Red "Corvette" Dash lettering
-Llyods floor mats with "Corvette Racing" on them
-Corvette Mods Column Lock Bypass
-Metal Shift boot ring (Locks boot in place and will never break like the factory plastic one)

Originally Posted by Bruce Wayne

That thing is gorgeous. Very nicely done.

Originally Posted by SgtRod

Nice build. Proly a small detail but i would have put the side exhaust on the pass side. Large cams reek of gas.

did you do all these mods or did you buy it with some done? Is that an ls6 making 500rwhp?

Any video?