Gauging Interest - Urethane Rear Bumper with duckbill wing
#1
Former Vendor
Thread Starter
Gauging Interest - Urethane Rear Bumper with duckbill wing
I'll keep this short and sweet. We currently have the Xtreme rear bumper available, but it requires a bit more fit and finish than most guys would like. I have a new manufacturer that can build me the exact bumper or really similar in urethane...that will have an awesome fit and finish guaranteed. Now don't hold me to this, as I don't know what's the price will be yet. I will try to keep it as affordable as possible. I'm hoping to have it in the $599-699 range. It could go up a bit, but I'll do what I can to keep it low.
Here's a few pictures of what it would look like, it would just be urethane instead of fiberglass. Post up if interested
Here's a few pictures of what it would look like, it would just be urethane instead of fiberglass. Post up if interested
The following 6 users liked this post by Quik Z06:
ArmchairArchitect (12-12-2018),
Black 03 Z06 (09-08-2017),
c5BlackBeauty (02-19-2018),
Fsharp9 (01-04-2018),
Patches (02-17-2017),
and 1 others liked this post.
The following users liked this post:
Patches (02-17-2017)
#3
Team Owner
It looks really good, reminiscent of the 'Specter-Werkes" rear fascia, from a number of years ago.....however, I thought the story was that the S-W fascias took a lot of work to get fitted and looking proper.
If you could get them at a decent price point, and as previously stated, in a easily useable state, you might be on to something.
If you could get them at a decent price point, and as previously stated, in a easily useable state, you might be on to something.
Last edited by leadfoot4; 02-18-2017 at 08:22 AM.
The following 2 users liked this post by leadfoot4:
Black 03 Z06 (09-08-2017),
Patches (02-17-2017)
The following users liked this post:
Patches (02-17-2017)
The following users liked this post:
mtndv8 (02-24-2017)
The following users liked this post:
Patches (02-17-2017)
#9
Melting Slicks
I'm not usually a big fan of add on spoilers and such but I have to go with others in saying that the C5 should have come from the factory with that setup. I think its very complimentary to the beautiful lines of the c5. Very nice!! Take care!
The following users liked this post:
Patches (02-17-2017)
#11
Race Director
Member Since: May 2003
Location: Iowa
Posts: 13,995
Received 2,706 Likes
on
1,668 Posts
St. Jude Donor '03-'04-'05-'06-'07-'08-'09-'10-'11-'12-'13-'14-'15-'16'-'17-‘18-'19-'20-'21-'22-
'23-'24
That looks awesome, esp on the wide body C5s
The following users liked this post:
Patches (02-17-2017)
#12
Team Owner
Joel's wide body C5 with the CC rear. Looks significantly smaller from the front so I think it's perfect. This is the bumper that will be reproduced in urethane.
Last edited by Patches; 02-21-2017 at 01:22 PM.
The following users liked this post:
Patches (02-17-2017)
The following users liked this post:
Patches (02-17-2017)
The following users liked this post:
Patches (02-17-2017)
The following users liked this post:
Patches (02-18-2017)