Leave in Place-Jacking Pucks
02-16-2012, 05:27 AM
#43
I just ordered a set also. I got a set of the aluminum ones that I bought back in 98, but I have had them to slide around on some jacks.
Leave in sounds like the way to go.
Leave in sounds like the way to go.
02-17-2012, 06:40 PM
#46
Race Director
Member Since: Jul 2007
Location: Reno is so close to Hell you can see Sparks , State Of Confusion
Posts: 18,681
Likes: 0
Received 38 Likes
on
23 Posts
St. Jude Donor '12-'13-'14
I have a question on these, I have a lowered C5 and I do get close to some speedbumps, What are the chances of these scrapping the speedbump and falling off? I do have rail savers installed, Will these hang lower then the savers?
Mr.Bill
Mr.Bill
06-06-2012, 03:44 PM
#47
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Very small chance...they barley hang below the car at all, if any. If you hit the pucks you have bigger things to worry about 
07-19-2012, 09:57 AM
#52
Race Director
I finally got around to installing mine last weekend. Loving them!
Anyone have these with Elite Engineering Frame Rails ?
07-28-2012, 12:11 AM
#54
I love my pucks and was wondering the same thing about the Elite frame rails, but from the looks of it the rails have welded on plates that cover the jacking puck holes so you can jack from the rail itself. I really need some rail protectors though.
08-03-2012, 07:51 PM
#55
Instructor
Member Since: Jan 2010
Location: NYC
Posts: 179
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Jim, I received my set the other day. They are smaller than I thought they would be (the diameter of the saddle pad on my floor jack is larger) but they seem like they would do the trick just fine. 
08-27-2012, 05:04 PM
#59
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Finally back in stock and ready to ship!
Leave in place Corvette Jacking Pucks....Pop them in and forget about them, they will be there when you need them.
The ultimate jacking solution for your Corvette C6 or C5. Brand new, leave in place jacking pucks. Our Corvette jacking pucks are low profile and will last as long as you own your car. They "pop" right in to your jack hole and you can then leave them in place without ever needing to remove them. The easily snap into place and will be there if you ever need to jack up your car. The are not noticeable under the car and look like a factory OEM piece (not sure why GM did not include them in the first place). They can also be popped right back out if you ever need to remove them. Made from durable plastic, they will last the life of your car and you can rest assured you will never be stuck in a situation where you need to jack up the car and do not have jacking pucks.
Very affordable and the best solution for Jacking up your car....
in stock and ready to roll
Leave in Place Corvette Jacking Pucks
Leave in place Corvette Jacking Pucks....Pop them in and forget about them, they will be there when you need them.
The ultimate jacking solution for your Corvette C6 or C5. Brand new, leave in place jacking pucks. Our Corvette jacking pucks are low profile and will last as long as you own your car. They "pop" right in to your jack hole and you can then leave them in place without ever needing to remove them. The easily snap into place and will be there if you ever need to jack up your car. The are not noticeable under the car and look like a factory OEM piece (not sure why GM did not include them in the first place). They can also be popped right back out if you ever need to remove them. Made from durable plastic, they will last the life of your car and you can rest assured you will never be stuck in a situation where you need to jack up the car and do not have jacking pucks.
Very affordable and the best solution for Jacking up your car....
in stock and ready to roll
Leave in Place Corvette Jacking Pucks
