Build sheet location - CorvetteForum - Chevrolet Corvette Forum Discussion

Go Back   >
Log In 
Register FAQ Search Today's Posts Mark Forums Read Vendor Directory

C5 Tech
Corvette Tech/Performance: LS1 Corvette Technical Info, Internal Engine, External Engine, Tech Topics, Basic Tech, Maintenance, How to Remove & Replace Sponsored by
Dart Machinery

Build sheet location

Reply
 
 
 
Thread Tools Search this Thread
Old 04-16-2006, 11:07 AM   #1
redjetty
CF Senior Member
Thread Starter
 
redjetty's Avatar
 
Member Since: Mar 2006
Location: N.W. Arkansas
Posts: 756
Thanks: 0
Thanked 1 Time in 1 Post
Default Build sheet location

can someone tell me where i can find my build sheet on my 04? i read someplace in here that its found in the front re-bar??? what would that be ?,, thanks rj
redjetty is offline   Reply With Quote
Old 04-16-2006, 11:41 AM   #2
purrvert
CF Senior Member
 
purrvert's Avatar
 
Member Since: Aug 2004
Location: satellite beach fl
Posts: 346
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Check your glovebox.
purrvert is offline   Reply With Quote
Old 04-16-2006, 12:57 PM   #3
wamara
CF Senior Member
Cruise-In II Veteran
 
wamara's Avatar
 
Member Since: Sep 2000
Location: ABQ NM
Posts: 5,727
Thanked 4 Times in 4 Posts
Default

Quote:
Originally Posted by purrvert
Check your glovebox.
What you are referring to in the glovebox is NOT the build sheet.

redjetty,
The build sheet is a folded printer sheet in the front crossmember frame rail (which is a hollow boxed member). I think the only way you can get to it is by removing the front fascia. An easier way to obtain one (albeit not "original") is to order one from the NCM.
wamara is offline   Reply With Quote
Old 04-16-2006, 01:15 PM   #4
SpeedyZ
CF Senior Member
Support Corvetteforum!
 
SpeedyZ's Avatar
 
Member Since: Oct 2004
Location: Southwest Virginia
Posts: 1,383
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by wamara
What you are referring to in the glovebox is NOT the build sheet.

redjetty,
The build sheet is a folded printer sheet in the front crossmember frame rail (which is a hollow boxed member). I think the only way you can get to it is by removing the front fascia. An easier way to obtain one (albeit not "original") is to order one from the NCM.


You are correct, you have to remove the front fascia (bumper cover) and the front bumper (foam pad) then you reach in the end of the front impact bar (front frame cross section) and pull out the sheet.

Anyone know how much the NCM charges for the sheet?
SpeedyZ is offline   Reply With Quote
Old 04-16-2006, 02:10 PM   #5
wamara
CF Senior Member
Cruise-In II Veteran
 
wamara's Avatar
 
Member Since: Sep 2000
Location: ABQ NM
Posts: 5,727
Thanked 4 Times in 4 Posts
Default

Quote:
Originally Posted by SpeedyZ
Anyone know how much the NCM charges for the sheet?
I suspect the NCM's website would state the cost.
wamara is offline   Reply With Quote
Old 04-16-2006, 06:38 PM   #6
GUSTO14
CF Senior Member
 
GUSTO14's Avatar
 
Member Since: Sep 2003
Location: eastern NC
Posts: 4,433
Thanked 145 Times in 135 Posts
Default

Quote:
Originally Posted by SpeedyZ


You are correct, you have to remove the front fascia (bumper cover) and the front bumper (foam pad) then you reach in the end of the front impact bar (front frame cross section) and pull out the sheet.

Anyone know how much the NCM charges for the sheet?
I just purchased two, one for my 2000 and one for my 1985. They were $25 and $30 laminated. I can't remember which was which, but it is I believe $10 more if you are not a member of the NCM. They look terrific.

Good luck... GUSTO
GUSTO14 is offline   Reply With Quote
Old 04-16-2006, 07:03 PM   #7
SteveDoten
CF Senior Member
Cruise-In VII Veteran
 
SteveDoten's Avatar
 
Member Since: Sep 2003
Location: Farmington/DeerPark CT/NY
Posts: 5,091
Thanked 13 Times in 10 Posts
Default

i've got a thread on this, let me find it, have pics and location
SteveDoten is offline   Reply With Quote
Old 04-16-2006, 07:06 PM   #8
SteveDoten
CF Senior Member
Cruise-In VII Veteran
 
SteveDoten's Avatar
 
Member Since: Sep 2003
Location: Farmington/DeerPark CT/NY
Posts: 5,091
Thanked 13 Times in 10 Posts
Default

here ya go, if you are local i'll help you remove the build sheet(takes about an hour)

http://forums.corvetteforum.com/show...highlight=ncrs

SteveDoten is offline   Reply With Quote
Go Back   CorvetteForum - Chevrolet Corvette Forum Discussion >
Reload this Page
  • Build sheet location
  •  
     
    Reply

    Related Topics
    Thread Thread Starter Forum Replies Last Post
    Build Sheet Trlcruise C4 General Discussion 1 10-11-2014 04:48 AM
    Build Sheet RockHeadss C4 General Discussion 6 02-06-2010 12:21 PM
    Build Sheets kevinquirk C3 General 13 04-17-2009 05:32 PM
    Build sheet question C3Paul C3 General 11 09-11-2008 02:18 PM
    1969 build sheets RCB69L36 C3 Tech/Performance 2 01-21-2003 09:46 AM


    Tags
    1979, 1985, 2003, attain, build, c4, c5, corvette, factory, located, location, placement, read, sheet, sheets

    Thread Tools Search this Thread
    Search this Thread:

    Click for Advanced Search

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is Off
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off

    Forum Jump


    All times are GMT -4. The time now is 03:06 AM.