Go Back   Corvette Forum > C5 Corvettes, 1997 - 2004 > C5 Tech
Sign in using an external account
Register Forgot Password?
Register Search Today's Posts Mark Forums Read FAQ Vendor Directory
Search
C5 Tech
Corvette Tech/Performance: LS1 Corvette Technical Info, Internal Engine, External Engine, Tech Topics, Basic Tech, Maintenance, How to Remove & Replace Sponsored by
Karl Chevrolet

Welcome to Corvetteforum.com!
Welcome to Corvetteforum.com.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join Corvetteforum.com today!


Corvette Store
 
 
C7 Parts & Accessories
C6 Parts & Accessories
C5 Parts & Accessories
C4 Parts & Accessories
C3 Parts & Accessories
C2 Parts & Accessories
C1 Parts & Accessories
Wheels & Tires
Sponsored Ads
 
 
Vendor Directory
  
Reply
 
 
 
 
Thread Tools Search this Thread
Old 10-09-2011, 10:05 PM   #1
canadian99c5
Junior Member
 
Member Since: Aug 2011
Default P1571 ASR Desired Torque

what is this code its coming up with no comm tcs???
canadian99c5 is offline   Reply With Quote
Old 10-09-2011, 11:07 PM   #2
Bill Dearborn
Tech Contributor
 
Bill Dearborn's Avatar
 
Member Since: Oct 1999
Location: Charlotte (formerly Endicott, NY) NC
Default

DTC P1571 Traction Control Torque Request Circuit
Circuit Description
The PCM supplies 5 volts on the desired torque circuit to the Electronic Brake and Traction Control Module (EBTCM). The EBTCM toggles this 5 volt signal to a ground in order to produce a duty cycle signal. The signal is proportional to the amount of engine output torque reduction requested by the EBTCM. The EBTCM supplies this signal when it detects a wheel slip. In order to reduce engine output torque, the PCM reduces the amount of spark advance and in some cases, the PCM disables a number of fuel injectors. This diagnostic tests for a Desired Torque signal failure. If the PCM does not receive the Desired torque signal, this DTC sets.

Conditions for Running the DTC
• The traction control has not failed.
• The engine speed is greater than 500 RPM for 20 seconds.

Conditions for Setting the DTC
The desired torque signal is not received by the PCM for 3 seconds.

Action Taken When the DTC Sets
• The powertrain control module (PCM) stores the DTC information into memory when the diagnostic runs and fails.
• The malfunction indicator lamp (MIL) will not illuminate.
• The PCM records the operating conditions at the time the diagnostic fails. The PCM stores this information in the Failure Records.
Conditions for Clearing the MIL/DTC
• A last test failed, or the current DTC, clears when the diagnostic runs and does not fail.
• A history DTC clears after 40 consecutive warm-up cycles, if failures are not reported by this or any other emission related diagnostic.
• Use a scan tool in order to clear the MIL/DTC.
Diagnostic Aids
Important:
• Remove any debris from the PCM\TAC module connector surfaces before servicing the PCM\TAC module. Inspect the PCM\TAC module connector gaskets when diagnosing/replacing the modules. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion into the PCM\TAC modules.
• For any test that requires probing the PCM or a component harness connector, use the Connector Test Adapter Kit J 35616 . Using this kit prevents damage to the harness/component terminals. Refer to Using Connector Test Adapters in Wiring Systems.
• Do not perform this diagnostic procedure if the customer's concern is not related to the ABS and/or the Traction Control system(s).
• The following may cause an intermittent:
- Poor connections; Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.
- Corrosion
- Mis-routed harness
- Rubbed through wire insulation
- Broken wire inside the insulation
• For an intermittent condition, refer to Symptoms .


Bill
Bill Dearborn is online now   Reply With Quote
Old 10-09-2011, 11:22 PM   #3
canadian99c5
Junior Member
 
Member Since: Aug 2011
Default

Thanks for the reply I had my ebcm out to resolder what i could and put it back in and cleared all the codes after starting the car I got the pcm p1571 and the sdm u1040 codes I've been getting the 1255 code before thats why the soldering.. I have a used ebcm coming I've cleaned all the grounds and checked the fuses so i'm convinced ite the ebcm thats the problem wish me luck
canadian99c5 is offline   Reply With Quote
Old 10-09-2011, 11:22 PM
 
Go Back   Corvette Forum > C5 Corvettes, 1997 - 2004 > C5 Tech
Reload this Page P1571 ASR Desired Torque
 
 
 
Reply

Tags
1571, 1997, 99, asr, c5, cicuit, code, corvette, desired, fuse, p1571, pcm, race, request, torque, vette


Thread Tools Search this Thread
Search this Thread:

Click for Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump


All times are GMT -4. The time now is 07:51 PM.


Emails & Password Backup