I need a pic of the Convertible position switches
#1
Supporting Vendor
Thread Starter
Member Since: Sep 2007
Location: Pensacola Florida GO GATORS!!! www.rlsebring.com www.c6c7vette.com
Posts: 11,216
Received 174 Likes
on
92 Posts
St. Jude Donor '17
I need a pic of the Convertible position switches
I really don't want to go into what happened but I need a pic of the area under the uppermost B pillar trim just forward of the hydraulic pump that shows the bow position switches.
There are four switches in an area of about 6" radius. The 5 bow area pivot is right there with it. I want to say the manual calls them the SM7 switches.
My Mitchell or eSi disc doesn't seem to show a detailed area of how the switches are positioned or what they contact to be "Open" or "Closed". The top may have to be in the half up position to really see them well.
I can post a pic of the area if need be.
Thanks
There are four switches in an area of about 6" radius. The 5 bow area pivot is right there with it. I want to say the manual calls them the SM7 switches.
My Mitchell or eSi disc doesn't seem to show a detailed area of how the switches are positioned or what they contact to be "Open" or "Closed". The top may have to be in the half up position to really see them well.
I can post a pic of the area if need be.
Thanks
#5
If I don't have to take anything apart, and you can step by step me through what you need to see, I can do it for you now. My vert (09) is in the parking lot.
It will have to be an iPhone photo but i will get it as clear as I can.
It will have to be an iPhone photo but i will get it as clear as I can.
#6
Supporting Vendor
Thread Starter
Member Since: Sep 2007
Location: Pensacola Florida GO GATORS!!! www.rlsebring.com www.c6c7vette.com
Posts: 11,216
Received 174 Likes
on
92 Posts
St. Jude Donor '17
I was hoping that out of all the Verts on here some one would have the area exposed and could get a shot easily.
I am checking with Helms onLine now to see if they has a repair diagram of the area.
Thanks again
#8
Melting Slicks
I have a power top convertible and know exactly where the hydraulic pump is located and how to access that area. You want a picture of the switches? I am running out of daylight here and can probably snap a pic tomorrow.
Does this help?
Does this help?
Last edited by Vettlldo; 08-13-2009 at 08:24 PM.
#9
Supporting Vendor
Thread Starter
Member Since: Sep 2007
Location: Pensacola Florida GO GATORS!!! www.rlsebring.com www.c6c7vette.com
Posts: 11,216
Received 174 Likes
on
92 Posts
St. Jude Donor '17
I will be grateful. The switches are just ahead of the pump behind the upper B pillar trim and at the corner of the 5 Bow.
Thanks!
#10
Melting Slicks
#11
Supporting Vendor
Thread Starter
Member Since: Sep 2007
Location: Pensacola Florida GO GATORS!!! www.rlsebring.com www.c6c7vette.com
Posts: 11,216
Received 174 Likes
on
92 Posts
St. Jude Donor '17
Unfortunately not. The area is a little forward of the shot.
Here is a pic of the area. Hopefully my circle shows up showing the position switch in all it's glory not able to make contact with anything. This position results in the message on the DIC " Top not secured" and does not allow the tonnou (sp) to initionally open with the top in the opening position and not allowing the tonnou (sp) to close in the top going down position. The more I look at it, It's either not it the right place of it's missing something.
Here is a pic of the area. Hopefully my circle shows up showing the position switch in all it's glory not able to make contact with anything. This position results in the message on the DIC " Top not secured" and does not allow the tonnou (sp) to initionally open with the top in the opening position and not allowing the tonnou (sp) to close in the top going down position. The more I look at it, It's either not it the right place of it's missing something.
Last edited by RLSebring; 08-13-2009 at 10:19 PM.
#13
Melting Slicks
Unfortunately not. The area is a little forward of the shot.
Here is a pic of the area. Hopefully my circle shows up showing the position switch in all it's glory not able to make contact with anything. This position results in the message on the DIC " Top not secured" and does not allow the tonnou (sp) to initionally open with the top in the opening position and not allowing the tonnou (sp) to close in the top going down position. The more I look at it, It's either not it the right place of it's missing something.
Here is a pic of the area. Hopefully my circle shows up showing the position switch in all it's glory not able to make contact with anything. This position results in the message on the DIC " Top not secured" and does not allow the tonnou (sp) to initionally open with the top in the opening position and not allowing the tonnou (sp) to close in the top going down position. The more I look at it, It's either not it the right place of it's missing something.
#16
Le Mans Master
Member Since: Jul 2004
Location: Saraland Alabama
Posts: 5,857
Likes: 0
Received 3 Likes
on
2 Posts
St. Jude Donor '11-'12-'13-'14-'15-'16
I have a set of factory shop manuals on my '05 with power top.
On page 8-681 it shows power folding top limit switches replacement.
There is almost 150 pages of info in the manual relating to the folding top.
Do you have factory shop manuals on the car you are working on?
If not, surely someone in P'cola would have a set. Another idea is contact someone in the Pensacola or Miracle Strip Corvette club as maybe someone has a C6 convertible that can help you. If all else fails, I live in the Mobile area and I may be going to Foley tomorrow. I can take my manual and you could meet me and look at and copy the pages you need.
If you need to contact me just send me a PM.
Sanford in Saraland, Alabama
On page 8-681 it shows power folding top limit switches replacement.
There is almost 150 pages of info in the manual relating to the folding top.
Do you have factory shop manuals on the car you are working on?
If not, surely someone in P'cola would have a set. Another idea is contact someone in the Pensacola or Miracle Strip Corvette club as maybe someone has a C6 convertible that can help you. If all else fails, I live in the Mobile area and I may be going to Foley tomorrow. I can take my manual and you could meet me and look at and copy the pages you need.
If you need to contact me just send me a PM.
Sanford in Saraland, Alabama
#17
Supporting Vendor
Thread Starter
Member Since: Sep 2007
Location: Pensacola Florida GO GATORS!!! www.rlsebring.com www.c6c7vette.com
Posts: 11,216
Received 174 Likes
on
92 Posts
St. Jude Donor '17
I may have to break down and by some manuals. I have used GM's eSi on-line for just about everything up till now. I even tried haynes online to no avail.
I am always up for a road trip. I'll send a PM to get details. I certainly appreciate the offer.
Robert
I am always up for a road trip. I'll send a PM to get details. I certainly appreciate the offer.
Robert
I have a set of factory shop manuals on my '05 with power top.
On page 8-681 it shows power folding top limit switches replacement.
There is almost 150 pages of info in the manual relating to the folding top.
Do you have factory shop manuals on the car you are working on?
If not, surely someone in P'cola would have a set. Another idea is contact someone in the Pensacola or Miracle Strip Corvette club as maybe someone has a C6 convertible that can help you. If all else fails, I live in the Mobile area and I may be going to Foley tomorrow. I can take my manual and you could meet me and look at and copy the pages you need.
If you need to contact me just send me a PM.
Sanford in Saraland, Alabama
On page 8-681 it shows power folding top limit switches replacement.
There is almost 150 pages of info in the manual relating to the folding top.
Do you have factory shop manuals on the car you are working on?
If not, surely someone in P'cola would have a set. Another idea is contact someone in the Pensacola or Miracle Strip Corvette club as maybe someone has a C6 convertible that can help you. If all else fails, I live in the Mobile area and I may be going to Foley tomorrow. I can take my manual and you could meet me and look at and copy the pages you need.
If you need to contact me just send me a PM.
Sanford in Saraland, Alabama
#18
Supporting Vendor
Thread Starter
Member Since: Sep 2007
Location: Pensacola Florida GO GATORS!!! www.rlsebring.com www.c6c7vette.com
Posts: 11,216
Received 174 Likes
on
92 Posts
St. Jude Donor '17
Sanford, Pleasure meeting you and the wife today. I'll let you know how the top turns out. I am planning on getting on it in the morning if it's not raining.
Ya'll have a safe trip to Bowling Green.
Ya'll have a safe trip to Bowling Green.
#19