2006 Chevy Corvette - Heavily Modded Z51
#1
Safety Car
Thread Starter
2006 Chevy Corvette - Heavily Modded Z51
Car makes well over 950+ to the wheels.
Any Questions feel free to ask~
Engine Mods:
Cosmetic/Interior:
I am asking $43.500 for the car or best offer.The CONS: Gonna be straight up with the issues so there is no you didn't tell me...
Any Questions feel free to ask~
Engine Mods:
- 408CI
- Callies Crank Shaft
- Lunati link bar lifters
- Tick Performance blow stage 2 cam
- Diamond Pistons ( 9.5:1)
- Fore Double pump E85 flex set up - -10 feed -8 return, Fore Fuel rails
- Mighty Mouse Catch Can system - WILD
- D1350X injectors
- ECS 2200x 2.85 Grip tech Pulley - 20.5psi
- A&A Secondary Drive kit 8rib
- American Racing 1 7/8 Headers
- Monster Stage 3 Clutch
- NW 102 Throttlebody
- Meziere Electric Water Pump,
- Holly High Rise intake
- MGW short throw shifter
- TickPerformance Master
- Hinson MotorSport Engine/Trans mounts
- Acell Ceramic Plug wires
Cosmetic/Interior:
- Z06 front bumper
- Zr1 Front fenders
- Z06 Extreme Rear Fenders
- Zr1 Mudflap/Splash guards
- Zr1 carbon ceramic upgrade
- Aldan Coilovers
- Zr1 front/side carbon fiber side skirts
- Rear Carbon fiber Diffuser 2 Tip Center Exhaust
- Carbon Fiber Halo
- Carbon Fiber Roof
- Socal Garage Carbon steering wheel
- Hydro Dripped Grill
- Weld S77 Wheels/Beadlocks
- Eagle Eye LED tail lights...
- Morimoto c7 headlight upgrade
- Car was repainted wet sanded to 4000 grit and polished to a mirror like shine. Over 100 hrs of prep/paint/Polish. It has recently been ceramic coated as well. Has never seen snow, Currently wrapped in 3m Blue Flame.
I am asking $43.500 for the car or best offer.
- The oil pan gasket is leaking, I have used "right stuff" to minimize the leak but its still weeping on the driver side.. It is also possible the oil cooler block gasket is bad as well. As I ran a dedicated B&M cooler for the oil instead..
- The stock z51 transcooler lines were removed and made into a loop at the trans as the car was not road coursed and is a M6
- Clutch bleeder line burst and started a fire in the driver side cowl area. about a foot of wire was cut out and rewired. No issues, No dash or codes have popped after this..
Last edited by UmX; 10-20-2021 at 06:38 AM.
The following users liked this post:
CorvetteBrent (06-24-2019)
#2
Racer
Great looking 06! I saw it at Autorama and the paint is amazing. It was a real attention getter. Well deserving of an award. Looking for a ZO6 or GS but this is very tempting GLWS.
#3
Safety Car
Thread Starter
The following users liked this post:
CorvetteBrent (06-24-2019)
#6
Safety Car
Thread Starter
#8
Safety Car
Thread Starter
Car still has a lien. Clean title in hand. And please get the story right.. Guy claims I owe him money that I don't. Had no problem paying for the paint on my car, the motor work, and anything else I bought for the car. I also been on here for a long time and sold tons of stuff. With no issues.
Last edited by UmX; 02-29-2016 at 05:10 PM.
The following users liked this post:
CorvetteBrent (06-24-2019)
#11
Le Mans Master
#12
Safety Car
Thread Starter
The following users liked this post:
CorvetteBrent (02-18-2020)
#14
Safety Car
Thread Starter
#19
Safety Car
Thread Starter
bump - Going to Dr phil today for a last over haul dyno tune and test- To ensure everything is good to go on the car.
Last edited by UmX; 03-07-2017 at 10:27 AM.
#20
Le Mans Master
Car still has a lien. Clean title in hand. And please get the story right.. Guy claims I owe him money that I don't. Had no problem paying for the paint on my car, the motor work, and anything else I bought for the car. I also been on here for a long time and sold tons of stuff. With no issues.
The following 2 users liked this post by C U IN REARVEIW:
CorvetteBrent (02-18-2020),
UmX (03-09-2017)