Pic to enjoy....
. Congrats Rodney! That's flying
09-12-2011, 05:47 PM
#3
Former Vendor
Thread Starter
I agree.... That was only a 1.351 60ft. I am leaving off the footbrake (NO Transbrake or 2 step) and the car flat hooks now. It will not go faster in the 60ft until I have better air,the car is just out of power...
09-12-2011, 05:52 PM
#5
Former Vendor
Thread Starter
Year of the Z06: 2007
Tires used on the pass: M&H
Performance Mods (if any): Untouched LS7 long block, just the D1 blower and about every bolt on made. Electric water pump,overdrive balancer,flip drive,custom intercooler piping,modified intercooler,2" Kooks headers with no cats,B&B bullets,4L60E conversion,Coan converter,DSS HD Propshaft,ZR1 Diff, Quaife,DSS 1500 HP Axles,SFI Flywheel,Billet flywheel cone,Boostapump,60lb injectors,Pfadt coil overs with special springs,Pfadt rear sway bar,Dewitts custom radiator,Chromoly 6 pt cage,etc....... The car made 689 RWHP on EPP's Mustang Dyno.
Category submitted for: C6 Z06 power adder
60'............. 1.403
330'........... 3.953
660'........... 6.077
660’ mph... 115.57
1000'.......... 7.921
1320'.......... 9.482
1320’ mph… 144.50
Name of the track: Muncie Dragway
Date of pass: Oct. 16, 2010
Tires used on the pass: M&H
Performance Mods (if any): Untouched LS7 long block, just the D1 blower and about every bolt on made. Electric water pump,overdrive balancer,flip drive,custom intercooler piping,modified intercooler,2" Kooks headers with no cats,B&B bullets,4L60E conversion,Coan converter,DSS HD Propshaft,ZR1 Diff, Quaife,DSS 1500 HP Axles,SFI Flywheel,Billet flywheel cone,Boostapump,60lb injectors,Pfadt coil overs with special springs,Pfadt rear sway bar,Dewitts custom radiator,Chromoly 6 pt cage,etc....... The car made 689 RWHP on EPP's Mustang Dyno.
Category submitted for: C6 Z06 power adder
60'............. 1.403
330'........... 3.953
660'........... 6.077
660’ mph... 115.57
1000'.......... 7.921
1320'.......... 9.482
1320’ mph… 144.50
Name of the track: Muncie Dragway
Date of pass: Oct. 16, 2010
09-12-2011, 06:40 PM
#8
Advanced
Member Since: May 2010
Location: Frisco TX
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
Year of the Z06: 2007
Tires used on the pass: M&H
Performance Mods (if any): Untouched LS7 long block, just the D1 blower and about every bolt on made. Electric water pump,overdrive balancer,flip drive,custom intercooler piping,modified intercooler,2" Kooks headers with no cats,B&B bullets,4L60E conversion,Coan converter,DSS HD Propshaft,ZR1 Diff, Quaife,DSS 1500 HP Axles,SFI Flywheel,Billet flywheel cone,Boostapump,60lb injectors,Pfadt coil overs with special springs,Pfadt rear sway bar,Dewitts custom radiator,Chromoly 6 pt cage,etc....... The car made 689 RWHP on EPP's Mustang Dyno.
Category submitted for: C6 Z06 power adder
60'............. 1.403
330'........... 3.953
660'........... 6.077
660’ mph... 115.57
1000'.......... 7.921
1320'.......... 9.482
1320’ mph… 144.50
Name of the track: Muncie Dragway
Date of pass: Oct. 16, 2010
Tires used on the pass: M&H
Performance Mods (if any): Untouched LS7 long block, just the D1 blower and about every bolt on made. Electric water pump,overdrive balancer,flip drive,custom intercooler piping,modified intercooler,2" Kooks headers with no cats,B&B bullets,4L60E conversion,Coan converter,DSS HD Propshaft,ZR1 Diff, Quaife,DSS 1500 HP Axles,SFI Flywheel,Billet flywheel cone,Boostapump,60lb injectors,Pfadt coil overs with special springs,Pfadt rear sway bar,Dewitts custom radiator,Chromoly 6 pt cage,etc....... The car made 689 RWHP on EPP's Mustang Dyno.
Category submitted for: C6 Z06 power adder
60'............. 1.403
330'........... 3.953
660'........... 6.077
660’ mph... 115.57
1000'.......... 7.921
1320'.......... 9.482
1320’ mph… 144.50
Name of the track: Muncie Dragway
Date of pass: Oct. 16, 2010
09-12-2011, 07:03 PM
#11
Former Vendor
Thread Starter
09-12-2011, 07:17 PM
#13
Former Vendor
Thread Starter
Here are a couple pics of my ZR1 from the Fest also, I let my long time friend Kenny run it all weekend. He did a great job for a first timer with a 10.3X et
http://byrdphoto.smugmug.com/Cars/Ho...2_btbvSWj-A-LB
http://byrdphoto.smugmug.com/Cars/Ho...4_Br5kk93-A-LB
http://byrdphoto.smugmug.com/Cars/Ho...1_K5MJp9z-A-LB
09-13-2011, 12:15 AM
#15
Burning Brakes
Member Since: Jan 2005
Location: Shelby Township Michigan
Posts: 1,239
Likes: 0
Received 3 Likes
on
3 Posts
Those are some great times Rodney. When I was at the shop I forgot to check out what wheels and tires you're running on the rear. I hope to get a chance to hit the track this fall but I really need some tires that will hook on it. Trans has been working great since you rebuilt it and Phil has a good tune in it now so hopefully I can get it somewhere close to your times. Did you ever get a shop to make that trans part you showed me that has the inner splines that need to be machined? Thanks again.
09-13-2011, 01:34 AM
#16
Former Vendor
Member Since: Feb 2004
Location: Las Vegas NV
Posts: 10,876
Likes: 0
Received 8 Likes
on
7 Posts
St. Jude Donor '06 & '12
Im loving how you guys have really started racing more and more heavily. Its one thing to sell your transmissions to race shops. Its another beat the hell out of them yourselves. Great Job Rodney!!
