Corvette C6 Window Valet
#22
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,630
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
$139.99 shipped....No Group Purchase needed...
More info on the Window Valet and ordering below.
Corvette Window Valet
What is a Window Valet? The Window Valet plugs into the OBD port underneath the steering wheel. Once plugged in, it gives you remote control of your windows (a must for vert owners), three click of the unlock button on the Key FOB and the windows roll down. Three clicks of the lock button and the windows roll up. Allows you to roll the windows up and down from a distance. On hot days, you can vent the car before you even get to it. This is just one of the Valet Features, several more listed at the link below..
Checkout the video...
http://www.youtube.com/watch?v=y_IO9gMoyws
Corvette Window Valet
More info on the Window Valet and ordering below.
Corvette Window Valet
What is a Window Valet? The Window Valet plugs into the OBD port underneath the steering wheel. Once plugged in, it gives you remote control of your windows (a must for vert owners), three click of the unlock button on the Key FOB and the windows roll down. Three clicks of the lock button and the windows roll up. Allows you to roll the windows up and down from a distance. On hot days, you can vent the car before you even get to it. This is just one of the Valet Features, several more listed at the link below..
Checkout the video...
http://www.youtube.com/watch?v=y_IO9gMoyws
Corvette Window Valet
__________________
Last edited by southerncarparts; 02-06-2012 at 04:07 PM.
#28
Burning Brakes
This vendor is very good to deal with. I placed my order on Wednesday and parts arrived via FedEx on Saturday. In addition, they provide excellent communications.
#30
Drifting
I just picked one of these up from a forum member. Great product by the way. I just have a quick question... I noticed that when rolling the windows up or down, it pauses in 3-4 times in the sequence. It kind of goes, pauses for a split second, goes again, pauses, goes again, etc. It works fine, but i was just wondering if the pause is a common feature?
#31
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,630
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Should not be doing that...Sounds like you need to re index your windows. Directions to do that are in the valet instructions.
Thanks,
Jim
Thanks,
Jim
I just picked one of these up from a forum member. Great product by the way. I just have a quick question... I noticed that when rolling the windows up or down, it pauses in 3-4 times in the sequence. It kind of goes, pauses for a split second, goes again, pauses, goes again, etc. It works fine, but i was just wondering if the pause is a common feature?
#32
Drifting
Thanks for the heads up. But I checked the instructions and all I found is the following under troubleshooting:
"Troubleshooting: If the Window Valet will not perform the venting option, or if the windows stop just short of a perfect seal, it is likely that the window position sensors in the C6/XLR need to be recalibrated. The C6/XLR owner's manual explains how to do this. In summary, raise the window with the driver door panel “up” button and hold the “up” button for three extra seconds after the window reaches the top. Release the button, then press the “up” button again and hold for three additional seconds. Do this for each window. Normally, this process is used whenever the C6/XLR fails to seal the windows upon closing of the door; however, it also solves the Window Valet™ venting issue."
This basically says its for the sealing of the wodow issue and does not mention anything about the issue I'm having. Can you direct me to the "re-indexing" of my windows? Thanks.
"Troubleshooting: If the Window Valet will not perform the venting option, or if the windows stop just short of a perfect seal, it is likely that the window position sensors in the C6/XLR need to be recalibrated. The C6/XLR owner's manual explains how to do this. In summary, raise the window with the driver door panel “up” button and hold the “up” button for three extra seconds after the window reaches the top. Release the button, then press the “up” button again and hold for three additional seconds. Do this for each window. Normally, this process is used whenever the C6/XLR fails to seal the windows upon closing of the door; however, it also solves the Window Valet™ venting issue."
This basically says its for the sealing of the wodow issue and does not mention anything about the issue I'm having. Can you direct me to the "re-indexing" of my windows? Thanks.
#33
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,630
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Thanks for the heads up. But I checked the instructions and all I found is the following under troubleshooting:
"Troubleshooting: If the Window Valet will not perform the venting option, or if the windows stop just short of a perfect seal, it is likely that the window position sensors in the C6/XLR need to be recalibrated. The C6/XLR owner's manual explains how to do this. In summary, raise the window with the driver door panel “up” button and hold the “up” button for three extra seconds after the window reaches the top. Release the button, then press the “up” button again and hold for three additional seconds. Do this for each window. Normally, this process is used whenever the C6/XLR fails to seal the windows upon closing of the door; however, it also solves the Window Valet™ venting issue."
This basically says its for the sealing of the wodow issue and does not mention anything about the issue I'm having. Can you direct me to the "re-indexing" of my windows? Thanks.
"Troubleshooting: If the Window Valet will not perform the venting option, or if the windows stop just short of a perfect seal, it is likely that the window position sensors in the C6/XLR need to be recalibrated. The C6/XLR owner's manual explains how to do this. In summary, raise the window with the driver door panel “up” button and hold the “up” button for three extra seconds after the window reaches the top. Release the button, then press the “up” button again and hold for three additional seconds. Do this for each window. Normally, this process is used whenever the C6/XLR fails to seal the windows upon closing of the door; however, it also solves the Window Valet™ venting issue."
This basically says its for the sealing of the wodow issue and does not mention anything about the issue I'm having. Can you direct me to the "re-indexing" of my windows? Thanks.
raise the window with the driver door panel “up” button and hold the “up” button for three extra seconds after the window reaches the top. Release the button, then press the “up” button again and hold for three additional seconds. Do this for each window.
Thanks,
Jim
#34
Burning Brakes
Installed today within 1 Minute in my new GS. Great Product!
Not to well known over here, but I'm sure I could sell some here!
Care to ship some 10 or 20 overseas?
Not to well known over here, but I'm sure I could sell some here!
Care to ship some 10 or 20 overseas?