1" Wider Extended Carbon fiber ZR1 Side skirts and Mudflaps!! ** New Product **
#221
#222
Race Director
Finally!
Looking good and same question as above. Will the side match the current width of the C6 Z06 front wheel flap? Hopefully it will compliment each other very well.
I noticed most C6 ZR-1 replicas have the two front openings for brake ducts. Don't see that here. I sthis still being worked out or is that something you simply do not wish to incorporate into this design?
Will the mid section extend back about 2" like seen on some others?
How far out is the center section? 2" 3"?
And how far out are the outter coreners? 3"? 4"?
Curious as to how this will be mounted and held reliably in place.
So far, looking great!! Thansk for posting. Now I can go to bed.
Looking good and same question as above. Will the side match the current width of the C6 Z06 front wheel flap? Hopefully it will compliment each other very well.
I noticed most C6 ZR-1 replicas have the two front openings for brake ducts. Don't see that here. I sthis still being worked out or is that something you simply do not wish to incorporate into this design?
Will the mid section extend back about 2" like seen on some others?
How far out is the center section? 2" 3"?
And how far out are the outter coreners? 3"? 4"?
Curious as to how this will be mounted and held reliably in place.
So far, looking great!! Thansk for posting. Now I can go to bed.
Last edited by WICKEDFRC; 10-01-2014 at 08:07 PM.
#223
Drifting
Looks good... I have some similar feedback:
1. I have a front plate bracket that mounts through the stock brake duct cutout on the stock lip... will there be a cutout for airflow/cooling or an alternate plate mounting option sold with this lip (might be good to incorporate a plate mount option.
2. How low does it hang from the stock front fascia compared to the stock Z06 lip and stock ZR1 lip. I know the ZR1 lip runs a hair lower than the Z06 lip, but can't get a good feel for how low this one hangs.
3. Will this have an under-tray mount or require the ZR1 fascia reinforcement?
Great start and I can't wait to see this finished up and mounted a clean platform to see how it looks...
1. I have a front plate bracket that mounts through the stock brake duct cutout on the stock lip... will there be a cutout for airflow/cooling or an alternate plate mounting option sold with this lip (might be good to incorporate a plate mount option.
2. How low does it hang from the stock front fascia compared to the stock Z06 lip and stock ZR1 lip. I know the ZR1 lip runs a hair lower than the Z06 lip, but can't get a good feel for how low this one hangs.
3. Will this have an under-tray mount or require the ZR1 fascia reinforcement?
Great start and I can't wait to see this finished up and mounted a clean platform to see how it looks...
Finally!
Looking good and same question as above. Will the side match the current width of the C6 Z06 front wheel flap? Hopefully it will compliment each other very well.
I noticed most C6 ZR-1 replicas have the two front openings for brake ducts. Don't see that here. I sthis still being worked out or is that something you simply do not wish to incorporate into this design?
Will the mid section extend back about 20" like seen on some others?
How far out is the center section? 2" 3"?
And how far out are the outter coreners? 3"? 4"?
Curious as to how this will be mounted and held reliably in place.
So far, looking great!! Thansk for posting. Now I can go to bed.
Looking good and same question as above. Will the side match the current width of the C6 Z06 front wheel flap? Hopefully it will compliment each other very well.
I noticed most C6 ZR-1 replicas have the two front openings for brake ducts. Don't see that here. I sthis still being worked out or is that something you simply do not wish to incorporate into this design?
Will the mid section extend back about 20" like seen on some others?
How far out is the center section? 2" 3"?
And how far out are the outter coreners? 3"? 4"?
Curious as to how this will be mounted and held reliably in place.
So far, looking great!! Thansk for posting. Now I can go to bed.
#224
Platinum Supporting Vendor
Thread Starter
Specs will be posted shortly, this splitter is mounted on a Base C6. Version to fit ZR1/Z06/GS will come right after this one is done.
We'll keep you posted
We'll keep you posted
#225
Platinum Supporting Vendor
Thread Starter
PMs replied!
Lets do another Carbon Fiber Extended side skirt set for $650 shipped
Coupon code: EXTsideskirt650
Lets do another Carbon Fiber Extended side skirt set for $650 shipped
Coupon code: EXTsideskirt650
#230
Platinum Supporting Vendor
Thread Starter
These Carbon Fiber Extended side skirt sets retail at $754 shipped
This is your chance at another $650 shipped deal!
Coupon code: EXTsideskirt650
This is your chance at another $650 shipped deal!
Coupon code: EXTsideskirt650
#234
Platinum Supporting Vendor
Thread Starter
Thanks again for your orders guys, we really appreciate it!
News:Another couple of sets are NOW available at the smokin deal of $650 shipped
Item link:
http://www.c7carbon.com/corvette-zr1...on-fiber-p-494
Coupon code: EXTsideskirt650
News:Another couple of sets are NOW available at the smokin deal of $650 shipped
Item link:
http://www.c7carbon.com/corvette-zr1...on-fiber-p-494
Coupon code: EXTsideskirt650
#235
Platinum Supporting Vendor
Thread Starter
#238
Race Director
Monthly bump!!!
Here's to the projected C6 Z06 extended splitter..... Still waiting. Holding out.
Hoping it will have the center piece undertray!!
Any more progress/photos of the C6 splitter?
Here's to the projected C6 Z06 extended splitter..... Still waiting. Holding out.
Hoping it will have the center piece undertray!!
Any more progress/photos of the C6 splitter?
#240
Platinum Supporting Vendor
Thread Starter
Our spoilers have 2 threaded studs located in the 3rd brake light section and 1 threaded hole on each side of the spoiler's enclosed bottom for a total of 4 mounting points. Also with the spoiler's enclosed bottom it allows you to add optional double side tape for extra grip