[Z06] Best Cam Results on Stock LS7 With Intake & Headers.
#1
Melting Slicks
Thread Starter
Member Since: Mar 2002
Location: Toronto Ontario
Posts: 3,426
Likes: 0
Received 0 Likes
on
0 Posts
Best Cam Results on Stock LS7 With Intake & Headers.
Hey Guys,
I hear rumors of stock LS7 bolting on a set of American Racing or Kooks with Vararam & Cam pushing upward of 550+ rwhp.
Can you post some dynos and you modification list to back that up ?
I hear rumors of stock LS7 bolting on a set of American Racing or Kooks with Vararam & Cam pushing upward of 550+ rwhp.
Can you post some dynos and you modification list to back that up ?
#3
Melting Slicks
I have LG headers 1 3/4" w/ high flow cats, Stic it Performance CAI, and a Black Mamba cam from QM and make 545rwhp/505rwtq. Car ran a 10.69@132.7 last weekend with the stock clutch and Nitto NT05R drag radials. Car was tuned by Carlos at QM in Dallas. Getting ready to get the heads done next.
#5
Supporting Vendor
There are several vendors that can get you where you want to go. We have several cams that will get you to over 550rwhp. Our Lethal Cam will get you close, it will normally dyno around 535-545rwhp on most cars. To hit 550 you could go with our Punisher cam, it will hit close to 560 rwhp.
Here is a graph of one our Stage 3 Punisher Cam.
Punisher Cam - RR-Stage 3
Here is a graph of one our Stage 3 Punisher Cam.
Punisher Cam - RR-Stage 3
#6
#8
Melting Slicks
Thread Starter
Member Since: Mar 2002
Location: Toronto Ontario
Posts: 3,426
Likes: 0
Received 0 Likes
on
0 Posts
There are several vendors that can get you where you want to go. We have several cams that will get you to over 550rwhp. Our Lethal Cam will get you close, it will normally dyno around 535-545rwhp on most cars. To hit 550 you could go with our Punisher cam, it will hit close to 560 rwhp.
Here is a graph of one our Stage 3 Punisher Cam.
Punisher Cam - RR-Stage 3
Here is a graph of one our Stage 3 Punisher Cam.
Punisher Cam - RR-Stage 3
#9
Supporting Vendor
Member Since: Nov 2005
Location: Supporting the Corvette Community at Abel Chevrolet in Rio Vista, CA 707-374-6317 Ext.123
Posts: 14,498
Received 1,425 Likes
on
597 Posts
St. Jude Donor '08
Here is a sheet of mine. First run was literally cam and cold air intake only. Second run was the addition of long tubes only with a re-tune.
The current setup made 554/510 SAE. Mods are .238/.248, .610/.620 112+2 cam, ARH Long Tubes, K&N cold air and a tune, stock LS7 manifold and ZR1 mufflers. Heads are bone stock.
With literally a cam only the car made 518/462. That was with the stock air filter and completley stock exhaust from the engine back.
Since dyno numbers do not mean a thing, the car has ran 10.59 @ 134 MPH on Drag Radials.
The current setup made 554/510 SAE. Mods are .238/.248, .610/.620 112+2 cam, ARH Long Tubes, K&N cold air and a tune, stock LS7 manifold and ZR1 mufflers. Heads are bone stock.
With literally a cam only the car made 518/462. That was with the stock air filter and completley stock exhaust from the engine back.
Since dyno numbers do not mean a thing, the car has ran 10.59 @ 134 MPH on Drag Radials.
#12
Burning Brakes
There are some bolton and cam guys just killing it out there. I will let them chime in but it is getting better and better. This year should prove to be a pretty serious advance in corvette drag racing. I am not a drag buy but I enjoy seeing guys push the envelope. RobZ/Gary/&crew, RatttG, sebast19x, Jamie, Ranger, etc. The one thing I really love is the camaraderie. Pretty much everyone is willing to lend a helping hand. I think it is a pretty sweet gesture that guys are willing to help a fellow vette owner.
Those are some nice times Richie. your car may be one of the meanest sounding Z06 out there
RobZ, i might have to let you take my car down this year if you promise not to break anything
Those are some nice times Richie. your car may be one of the meanest sounding Z06 out there
RobZ, i might have to let you take my car down this year if you promise not to break anything
#13
Le Mans Master
There are some bolton and cam guys just killing it out there. I will let them chime in but it is getting better and better. This year should prove to be a pretty serious advance in corvette drag racing. I am not a drag buy but I enjoy seeing guys push the envelope. RobZ/Gary/&crew, RatttG, sebast19x, Jamie, Ranger, etc. The one thing I really love is the camaraderie. Pretty much everyone is willing to lend a helping hand. I think it is a pretty sweet gesture that guys are willing to help a fellow vette owner.
Those are some nice times Richie. your car may be one of the meanest sounding Z06 out there
RobZ, i might have to let you take my car down this year if you promise not to break anything
Those are some nice times Richie. your car may be one of the meanest sounding Z06 out there
RobZ, i might have to let you take my car down this year if you promise not to break anything
We'll talk about it on an overnight tuna trip this summer.
Back on topic.
#14
Supporting Vendor
Here is a Stage 4 comparison of the 2 cams.
Check out the graph- RR STage 4 Comparison - LETHAL vs Punisher
2007 Z06, Callaway, CAI, Heads, Ported LS7 intake & TB.
Check out the graph- RR STage 4 Comparison - LETHAL vs Punisher
2007 Z06, Callaway, CAI, Heads, Ported LS7 intake & TB.
#17
Melting Slicks
KB Intake
FAST 102
NW 102 TB
AR headers
Borla Stingers
EWP
Black Widow Cam
WCC heads
E85 tune
We are still playing with the tune see if we can find alil more HP..
#18
Former Vendor
Wow, at 3K RPM's you already making about 480RWTQ
I know you mentioned that you guys are still playing with the tune but if you like, have your tuner give me a call or send me a copy of your tune, I think I can clean up the bottom a little more and perhaps carry it through the curve and thus get you a little more torque and possibly more power as well.
The heat and elevation in AZ is not great for big power but lets see what our combined efforts can get us...I'm game!
Thanks,
Carlos
#19
Team Owner
Made 545/510 on LG header, QM Mamba cam, Haltech KB1, and fast 102.
#20
Pro
Member Since: Sep 2009
Location: Milwaukee Wisconsin
Posts: 576
Likes: 0
Received 0 Likes
on
0 Posts
Congrats Evilness...
Wow, at 3K RPM's you already making about 480RWTQ
I know you mentioned that you guys are still playing with the tune but if you like, have your tuner give me a call or send me a copy of your tune, I think I can clean up the bottom a little more and perhaps carry it through the curve and thus get you a little more torque and possibly more power as well.
The heat and elevation in AZ is not great for big power but lets see what our combined efforts can get us...I'm game!
Thanks,
Carlos
Wow, at 3K RPM's you already making about 480RWTQ
I know you mentioned that you guys are still playing with the tune but if you like, have your tuner give me a call or send me a copy of your tune, I think I can clean up the bottom a little more and perhaps carry it through the curve and thus get you a little more torque and possibly more power as well.
The heat and elevation in AZ is not great for big power but lets see what our combined efforts can get us...I'm game!
Thanks,
Carlos