[Z06] Custom Interior Trim - What A Differnce!
#1
Premium Supporting Vendor
Thread Starter
Member Since: Aug 2004
Location: ★ Performance Parts & Accessories ★ 1800 778 9898
Posts: 17,123
Received 279 Likes
on
222 Posts
St. Jude Donor '07-'08-'11-'12-'13-'14-'15-'16-'17
Custom Interior Trim - What A Differnce!
One of the best improvements with huge impact you could easily do, is to upgrade just a few plastic interior parts in your 2005-2011
Remember this is where you live when you drive the car. You deserve to be surrounded by quality interior trim. Just a few upgrades makes a huge difference!
The Finish:
Allow us to enhance your interior parts with our 3D Immersion process. This is not a “Stick on” laminate which looks cheap, cracks and yellows. This is the same process used by the auto industry including GM for years! We start by using genuine GM parts to ensure a perfect fit. We then begin our multi step process to achieve a unique stunning appearance. The finished product is then covered in our unique tough clear which is then polished to a show quality shine
_______________________________________
For Starters…
If you have a 2008 and up Factory shifter console, we can do your gauge cluster in the same matching GM pattern. This easy upgrade dramatically changes your interior. It creates a rich feel while complimenting your factory shifter console.
Below: 2008-2009 GM 1LT, 2LT, 3LT Pattern (Also shown here with our Spoke covers done in the same pattern)
Below: 2010-2011 GM 1LT, 2LT, 3LTt pattern
For 2008-09 custom gauge bezels or other custom interior items click here:http://store.tkoperformance.com/2008.html
For 2010-11 custom gauge bezels or other custom interior items click here: http://store.tkoperformance.com/2010.html
All Custom Gauge Cluster Bezels are $195
If you have a 2005 -2007...
Not only can we do your gauge cluster bezel but allow us to create a face lift to that silver rent a car looking shifter console too!
We can do your interior in either the GM 2008-2011 patterns or a carbon fiber finish & even wood. Just say the word!
Below: Blue Carbon Finish
Below: Our Gun Metal Carbon Fiber finish
One key step we were 1st to do & are known for, is finishing off the inside area of the 05-2011 bezels. This extra step is so important!
Because of the process and the characteristics of the film, the film can stretch in that area leaving a less then perfect finish. Most leave it this way!
We take the extra steps to make sure you get a quality O.E looking piece !
look at the way it reflects when its fired up!
Read more about the difference between TKO's custom interior and the rest.. http://tkoperformance.com/interiorcompare.html
For 2005-2007 custom gauge bezels or other custom interior items click here: http://store.tkoperformance.com/20052007.html
All custom gauge bezels are $195.00
How about 2005-2007 Shifter Console
We can do this in our Carbon finish or a beautiful burl wood too!
Lets change it up with a little warm wood:
For 2005-2007 custom gauge bezels or other custom interior items click here: http://store.tkoperformance.com/20052007.html
All custom Shifter console are $245
2006-2011 Steering wheel spokes:
Our covers rid your wheel of that remaining silver that stares you in the face. We manufactured these parts here to look amazing without taking your steering wheel apart!
Easy to install. Snap right into place! Use clear silicone or double sided tape to hold them in place! A lot of attention to detail went into creating these covers. The edges on our Steering wheel Spoke covers have a rounded lip which sinks into the crease between the leather which completely covers the stock piece and looks great from any angle!
Below: Spoke covers (with matching gauge cluster bezel)
Below: spokes over a radio control button wheel (with matching gauge cluster bezel)
Below: Our Spoke covers sitting on/over blue tooth buttons.
Choose from Plain (no wheel control buttons), Radio control buttons (buttons on the right) or Blue tooth (buttons on both sides)
For 2006-2007 steering wheel spokes click here: http://store.tkoperformance.com/20052007.html
For 2008-2009 Steering wheel spokes click here: http://store.tkoperformance.com/2008.html
For 2010-2012 steering wheel spokes click here: http://store.tkoperformance.com/2010.html
All spoke covers are on sale for $89.95
CALL FOR PACKAGE DEALS!!!!1800 778 9898
_______________________________________
Sure you can do more. Many do. But if you just add 1 or more of the above, you will be completely satisfied with your interior........for now
Feel free to send in parts, any part you would like to have done. We can apply any of our finishes to any part for any car or truck!
*Please allow approx 3 weeks to ship. WE NOW HAVE AN EXPEDITE SERVICE! We can turn your parts around in 7 bus days! Just call and ask about it!
*Refundable cores charges will apply. Refunded once returned in 15 days. No core charge if you send your own parts in!
FEEL FREE TO CALL WITH ANY QUESTIONS 1800778 9898
Remember this is where you live when you drive the car. You deserve to be surrounded by quality interior trim.
Remember this is where you live when you drive the car. You deserve to be surrounded by quality interior trim. Just a few upgrades makes a huge difference!
The Finish:
Allow us to enhance your interior parts with our 3D Immersion process. This is not a “Stick on” laminate which looks cheap, cracks and yellows. This is the same process used by the auto industry including GM for years! We start by using genuine GM parts to ensure a perfect fit. We then begin our multi step process to achieve a unique stunning appearance. The finished product is then covered in our unique tough clear which is then polished to a show quality shine
_______________________________________
For Starters…
If you have a 2008 and up Factory shifter console, we can do your gauge cluster in the same matching GM pattern. This easy upgrade dramatically changes your interior. It creates a rich feel while complimenting your factory shifter console.
Below: 2008-2009 GM 1LT, 2LT, 3LT Pattern (Also shown here with our Spoke covers done in the same pattern)
Below: 2010-2011 GM 1LT, 2LT, 3LTt pattern
For 2008-09 custom gauge bezels or other custom interior items click here:http://store.tkoperformance.com/2008.html
For 2010-11 custom gauge bezels or other custom interior items click here: http://store.tkoperformance.com/2010.html
All Custom Gauge Cluster Bezels are $195
If you have a 2005 -2007...
Not only can we do your gauge cluster bezel but allow us to create a face lift to that silver rent a car looking shifter console too!
We can do your interior in either the GM 2008-2011 patterns or a carbon fiber finish & even wood. Just say the word!
Below: Blue Carbon Finish
Below: Our Gun Metal Carbon Fiber finish
One key step we were 1st to do & are known for, is finishing off the inside area of the 05-2011 bezels. This extra step is so important!
Because of the process and the characteristics of the film, the film can stretch in that area leaving a less then perfect finish. Most leave it this way!
We take the extra steps to make sure you get a quality O.E looking piece !
look at the way it reflects when its fired up!
Read more about the difference between TKO's custom interior and the rest.. http://tkoperformance.com/interiorcompare.html
For 2005-2007 custom gauge bezels or other custom interior items click here: http://store.tkoperformance.com/20052007.html
All custom gauge bezels are $195.00
How about 2005-2007 Shifter Console
We can do this in our Carbon finish or a beautiful burl wood too!
Lets change it up with a little warm wood:
For 2005-2007 custom gauge bezels or other custom interior items click here: http://store.tkoperformance.com/20052007.html
All custom Shifter console are $245
2006-2011 Steering wheel spokes:
Our covers rid your wheel of that remaining silver that stares you in the face. We manufactured these parts here to look amazing without taking your steering wheel apart!
Easy to install. Snap right into place! Use clear silicone or double sided tape to hold them in place! A lot of attention to detail went into creating these covers. The edges on our Steering wheel Spoke covers have a rounded lip which sinks into the crease between the leather which completely covers the stock piece and looks great from any angle!
Below: Spoke covers (with matching gauge cluster bezel)
Below: spokes over a radio control button wheel (with matching gauge cluster bezel)
Below: Our Spoke covers sitting on/over blue tooth buttons.
Choose from Plain (no wheel control buttons), Radio control buttons (buttons on the right) or Blue tooth (buttons on both sides)
For 2006-2007 steering wheel spokes click here: http://store.tkoperformance.com/20052007.html
For 2008-2009 Steering wheel spokes click here: http://store.tkoperformance.com/2008.html
For 2010-2012 steering wheel spokes click here: http://store.tkoperformance.com/2010.html
All spoke covers are on sale for $89.95
CALL FOR PACKAGE DEALS!!!!1800 778 9898
_______________________________________
Sure you can do more. Many do. But if you just add 1 or more of the above, you will be completely satisfied with your interior........for now
Feel free to send in parts, any part you would like to have done. We can apply any of our finishes to any part for any car or truck!
*Please allow approx 3 weeks to ship. WE NOW HAVE AN EXPEDITE SERVICE! We can turn your parts around in 7 bus days! Just call and ask about it!
*Refundable cores charges will apply. Refunded once returned in 15 days. No core charge if you send your own parts in!
FEEL FREE TO CALL WITH ANY QUESTIONS 1800778 9898
Remember this is where you live when you drive the car. You deserve to be surrounded by quality interior trim.
__________________
Serving The Corvette Forum For 21 Years!!
Allow us to add you to the list of extremely satisfied customers.
Order Securely Online 24/7: http://tkoperformance.com/index.html
Feel Free To Contact Us By Phone: 1800 -778- 9898 Monday- Friday 9:00am to 4:30pm
Click Here: http://www.facebook.com/pages/TKO-Pe...e/367433626633
Serving The Corvette Forum For 21 Years!!
Allow us to add you to the list of extremely satisfied customers.
Order Securely Online 24/7: http://tkoperformance.com/index.html
Feel Free To Contact Us By Phone: 1800 -778- 9898 Monday- Friday 9:00am to 4:30pm
Click Here: http://www.facebook.com/pages/TKO-Pe...e/367433626633
Last edited by TKO Performance; 11-30-2011 at 05:40 PM.
#2
I'm a little hesitant to take off the guage bezel. Probably not the only one. Maybe post up some basic instructions or pics for those of us who have never pulled the bezel off.
I'd probably order if I knew the process of removing the bezel.
I'd probably order if I knew the process of removing the bezel.
#3
Premium Supporting Vendor
Thread Starter
Member Since: Aug 2004
Location: ★ Performance Parts & Accessories ★ 1800 778 9898
Posts: 17,123
Received 279 Likes
on
222 Posts
St. Jude Donor '07-'08-'11-'12-'13-'14-'15-'16-'17
The readers digest version is..
There are no screws or bolts holding it in place. You basically pull and pop the gauge bezel out.
You will get about 4-5 inches out but now you have to just unplug the wires. Most plug are a Male/Female type snap in. Gently spread the “female” plastic fins and the plugs comes out.
For the pods (the two strip of buttons on the left and right) Its easier to unscrew the 3 screws on each side and the pack of buttons fall right out.
Reverse the direction to install.
Sounds easy because it is. We hear this all the time. Then people say “oh I’ll just take it to the dealer”……………..no one goes. They all do it themselves. If you had any questions, you could always call us.
Thanks
#7
Premium Supporting Vendor
Thread Starter
Member Since: Aug 2004
Location: ★ Performance Parts & Accessories ★ 1800 778 9898
Posts: 17,123
Received 279 Likes
on
222 Posts
St. Jude Donor '07-'08-'11-'12-'13-'14-'15-'16-'17
Feel Free to pm your number and I can always call you
Thanks
Ed
#8
Premium Supporting Vendor
Thread Starter
Member Since: Aug 2004
Location: ★ Performance Parts & Accessories ★ 1800 778 9898
Posts: 17,123
Received 279 Likes
on
222 Posts
St. Jude Donor '07-'08-'11-'12-'13-'14-'15-'16-'17
However you have mail..
#9
Once I get that figured out, I'll give ya a call.
#11
Premium Supporting Vendor
Thread Starter
Member Since: Aug 2004
Location: ★ Performance Parts & Accessories ★ 1800 778 9898
Posts: 17,123
Received 279 Likes
on
222 Posts
St. Jude Donor '07-'08-'11-'12-'13-'14-'15-'16-'17
If not , send me the piece and we can apply any finish you want and then cover it deep in clear and then polish it to a show quality shine..
Call me if you want.
Starting to get a littl bz now that the colder weather is coming. (People are sending many of their parts for us to do)..
Thank you
Ed
Last edited by TKO Performance; 10-25-2011 at 09:49 PM.
#14
Premium Supporting Vendor
Thread Starter
Member Since: Aug 2004
Location: ★ Performance Parts & Accessories ★ 1800 778 9898
Posts: 17,123
Received 279 Likes
on
222 Posts
St. Jude Donor '07-'08-'11-'12-'13-'14-'15-'16-'17
Thanks. As for the wood. yea I guess its an acquired taste. Its actually pretty popular. We get a lot of requests for it. Different colors, grains.. Obviously looks better in person then pictures.
But I hear you..
No, but our gun metal sure does look like it.
Since Carbon fibers characteristics are "light and strong" typically you would want to replace any part with carbon to shave & save weight.
To do interior parts in real carbon it would require a plug, mold (with tabs and reverse lips/angles).. A center console would cost around $1500-2000
Not worth it for the minimal weight savings.
So that would only leave doing it purely for the aesthetics... It can be done but wrapping real carbon fiber over an existing piece will also cost about the same $1500-2000. Not to mention it weighs much more then the stock piece. This is because of the amount of resin used which could play into fitting issues, yellowing & or cracking..
We can achieve the same look without the weight, the problems and the cost.
3d Immersion (which is what we do) is the same process the auto industry has been using for years (for wood..etc)
Same process GM uses now for the 2008-2012 interior center shifter consoles. The GM patterns don't look like carbon fiber (on purpose) they are merely a design...
But I hear you..
No, but our gun metal sure does look like it.
Since Carbon fibers characteristics are "light and strong" typically you would want to replace any part with carbon to shave & save weight.
To do interior parts in real carbon it would require a plug, mold (with tabs and reverse lips/angles).. A center console would cost around $1500-2000
Not worth it for the minimal weight savings.
So that would only leave doing it purely for the aesthetics... It can be done but wrapping real carbon fiber over an existing piece will also cost about the same $1500-2000. Not to mention it weighs much more then the stock piece. This is because of the amount of resin used which could play into fitting issues, yellowing & or cracking..
We can achieve the same look without the weight, the problems and the cost.
3d Immersion (which is what we do) is the same process the auto industry has been using for years (for wood..etc)
Same process GM uses now for the 2008-2012 interior center shifter consoles. The GM patterns don't look like carbon fiber (on purpose) they are merely a design...
Last edited by TKO Performance; 10-26-2011 at 10:50 AM.
#15
My bro has 4LT and I've got 3LZ. Gonna have to compare to another vette.
#16
Premium Supporting Vendor
Thread Starter
Member Since: Aug 2004
Location: ★ Performance Parts & Accessories ★ 1800 778 9898
Posts: 17,123
Received 279 Likes
on
222 Posts
St. Jude Donor '07-'08-'11-'12-'13-'14-'15-'16-'17
Your miss reading what I said... The original question from KLRBEE2 asked why he did not see a listing for a 3LZ pattern.
My answer was that I believe the 3LZ is a lighter silver (then the 1,2,3 LT's) which they don't make a film for us to use (to refinish the parts).
The 1,2,3LT's are a darker almost black with grey dots (shown above).
However I know for sure the lighter silver like pattern is what’s on the 4LT.
So if I'm correct about the 3LZ then both the 3LZ and the 4LT are the same and we can't finish those interiors. They don't make the film.
The only option would be for us to do the top center shifter console piece in one of the finish's we list. Then we can do the entire interior
#17
Okay, the trim I'm looking at would be something similar to this...
Would like to get the 06 wheel spokes in that color and some sort of 'sleeve' or cover for the gauge cluster pods.
Its sort of a smooth flat black.
EDIT: If it helps, this is a center console from a Centennial edition.
Would like to get the 06 wheel spokes in that color and some sort of 'sleeve' or cover for the gauge cluster pods.
Its sort of a smooth flat black.
EDIT: If it helps, this is a center console from a Centennial edition.
Last edited by Jawnathin; 10-26-2011 at 08:52 PM.
#18
Racer
Got mine from TKO and I installed it myself in about 40 mins. Not complicated at all.......
#19
Your miss reading what I said... The original question from KLRBEE2 asked why he did not see a listing for a 3LZ pattern.
My answer was that I believe the 3LZ is a lighter silver (then the 1,2,3 LT's) which they don't make a film for us to use (to refinish the parts).
The 1,2,3LT's are a darker almost black with grey dots (shown above).
However I know for sure the lighter silver like pattern is what’s on the 4LT.
So if I'm correct about the 3LZ then both the 3LZ and the 4LT are the same and we can't finish those interiors. They don't make the film.
The only option would be for us to do the top center shifter console piece in one of the finish's we list. Then we can do the entire interior
My answer was that I believe the 3LZ is a lighter silver (then the 1,2,3 LT's) which they don't make a film for us to use (to refinish the parts).
The 1,2,3LT's are a darker almost black with grey dots (shown above).
However I know for sure the lighter silver like pattern is what’s on the 4LT.
So if I'm correct about the 3LZ then both the 3LZ and the 4LT are the same and we can't finish those interiors. They don't make the film.
The only option would be for us to do the top center shifter console piece in one of the finish's we list. Then we can do the entire interior
#20
Premium Supporting Vendor
Thread Starter
Member Since: Aug 2004
Location: ★ Performance Parts & Accessories ★ 1800 778 9898
Posts: 17,123
Received 279 Likes
on
222 Posts
St. Jude Donor '07-'08-'11-'12-'13-'14-'15-'16-'17
Okay, the trim I'm looking at would be something similar to this...
Would like to get the 06 wheel spokes in that color and some sort of 'sleeve' or cover for the gauge cluster pods.
Its sort of a smooth flat black.
EDIT: If it helps, this is a center console from a Centennial edition.
Would like to get the 06 wheel spokes in that color and some sort of 'sleeve' or cover for the gauge cluster pods.
Its sort of a smooth flat black.
EDIT: If it helps, this is a center console from a Centennial edition.
800 778 9898
BTW, Just got another box today with a part in it. All I know is its from TX! Even if we talk and your sending the part right out to get done/finished ..PLEASE you still need to place a note in there with your name and number. I get about 5-6 boxes a day with parts to be done. Thanks
Ed
Last edited by TKO Performance; 10-28-2011 at 07:57 AM.