FI C7 dyno sheet post here!
11-24-2014, 06:19 PM
#1
Drifting
Thread Starter
FI C7 dyno sheet post here!
Google is turning up so few dyno sheets so far. Any more out there?
Last edited by imxz28; 06-22-2015 at 07:45 PM.
11-28-2014, 03:56 PM
#6
Supporting Vendor
LMR1200HP Twin Turbo
2014 Corvette Automatic
LMR1200HP Supercharged and Nitrous
Last pull we made with nitrous hit 1292wrhp. I will have to find the graph.
2014 Corvette Automatic
LMR1200HP Supercharged and Nitrous
Last pull we made with nitrous hit 1292wrhp. I will have to find the graph.
__________________
Worlds Quickest C8 Corvette 8.83@160MPH
FIRST C7 Corvette in the 7's & 9's
FIRST C7 Corvette in the 7's & 9's
2019 ZR1 LT5 8.874 @ 155
Current C7 World Record Holder 7.55 @ 184 MPH
Quickest and Fastest GEN5 LT Powered Vehicle
LMR1200HP Supercharged C7 8.84 @ 160
LMR1200HP Twin Turbo C7 9.35@155mph-2014
2 TIME OUTLAW DRAG RADIAL LSX CHAMPION 2008/2010
9.47 ZR1 Corvette-2009
LATE MODEL RACECRAFT
713-466-9900
LateModelRacecraft.com
Too many PMs, please call or email instead, thanks!
Current C7 World Record Holder 7.55 @ 184 MPH
Quickest and Fastest GEN5 LT Powered Vehicle
LMR1200HP Supercharged C7 8.84 @ 160
LMR1200HP Twin Turbo C7 9.35@155mph-2014
2 TIME OUTLAW DRAG RADIAL LSX CHAMPION 2008/2010
9.47 ZR1 Corvette-2009
LATE MODEL RACECRAFT
713-466-9900
LateModelRacecraft.com
Too many PMs, please call or email instead, thanks!
Last edited by Late Model Racecraft; 11-28-2014 at 04:01 PM.
11-29-2014, 09:56 PM
#8
Drifting
Thread Starter
More dyno
Here's a few more:
Edelbrock E-Froce on bone stock C7
.
.
2014 Procharger with A6
.
.
2014 Vortech with headers
.
.
See description near the top of the chart below
.
Edelbrock E-Froce on bone stock C7
.
.
2014 Procharger with A6
.
.
2014 Vortech with headers
.
.
See description near the top of the chart below
.
Last edited by imxz28; 12-02-2014 at 12:41 AM.
12-12-2014, 07:46 AM
#10
Instructor
6,500 ft elevation, D1SC Procharger, 8.0 psi Stock to 10 psi Cam and Meth
Before Headers and Exhaust
After Headers and Exhaust
After Cam and Meth (Snow's new C7 Meth Kit - 9.3 psi)
Procharger D1SC, 9.3psi Boost, Cam, Snow Meth 50/50 (first C7 kit - 2016), ARH 2" Headers, Billy Boat Fusion Mufflers, RX Separator and Can.
D1SC with Stock Motor vs. D1SC with Headers vs. D1SC with Cam and Meth
Last edited by Little Red Corvette1; 06-29-2016 at 06:29 PM. Reason: Added Dyno Chart After Cam and Meth was Installed
12-14-2014, 02:16 AM
#13
Former Vendor
Member Since: May 2008
Location: Tacoma WA
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
Here's a Procharger supercharger kit on a MY2015 Corvette C7 with 2" Headers that is otherwise completely stock:
http://i60.tinypic.com/2ry3vjb.jpg
http://i59.tinypic.com/120to34.jpg
http://i60.tinypic.com/ajwchk.jpg
http://i60.tinypic.com/2ry3vjb.jpg
http://i59.tinypic.com/120to34.jpg
http://i60.tinypic.com/ajwchk.jpg
12-14-2014, 07:17 PM
#15
Tech Contributor
Member Since: Jan 2006
Location: Saint Louis MO
Posts: 4,761
Likes: 0
Received 219 Likes
on
110 Posts
St. Jude Donor '14-'15
Eh, LMR put theirs up, so I don't feel bad about posting this. 
No laughing gas, and not the best run... 600wtq at 3000 (on a centri - roots can obviously do this but fall off a cliff by 4500).
Attachment 48369778
No laughing gas, and not the best run... 600wtq at 3000 (on a centri - roots can obviously do this but fall off a cliff by 4500).
Attachment 48369778
Last edited by Theta; 12-14-2014 at 07:23 PM.
12-19-2014, 06:46 PM
#16
Drifting
Thread Starter
ECS with only 3 mods: SC, ARH, Meth
.
.
.
.
.
.
Last edited by imxz28; 01-05-2015 at 01:39 AM.
03-16-2015, 01:22 AM
#17
Drifting
Thread Starter
Another one I collected from a forum member.
Procharger at 7lbs.
Installed and tuned by Chuck Mallett
.
Procharger at 7lbs.
Installed and tuned by Chuck Mallett
.
03-16-2015, 12:16 PM
#20
Drifting
Thread Starter