What mods are you doing to your vette over the winter?
12-14-2009, 08:01 PM
#1
Burning Brakes
Thread Starter
Member Since: Feb 2007
Posts: 872
Likes: 0
Received 0 Likes
on
0 Posts
What mods are you doing to your vette over the winter?
So what mods if any are you going to be doing to your vette when stored away for the winter?
I am adding some new custom seat covers and interior pieces along with seat heaters, also clean and paint the hood liner with a new decal, for now.
Then doing a good sanding and buffing of the old clear targa top as its starting to peel a bit and some painting of a few engine parts with a bit of added chrome.
All that should take me a while, if there is any extra time will install a new 4 channel amp and PAC thats been sitting around for a while.
I am adding some new custom seat covers and interior pieces along with seat heaters, also clean and paint the hood liner with a new decal, for now.
Then doing a good sanding and buffing of the old clear targa top as its starting to peel a bit and some painting of a few engine parts with a bit of added chrome.
All that should take me a while, if there is any extra time will install a new 4 channel amp and PAC thats been sitting around for a while.
12-14-2009, 10:46 PM
#4
Burning Brakes
12-15-2009, 08:55 AM
#6
Drifting
pm me
Last edited by WATTACAR; 12-15-2009 at 08:57 AM.
12-15-2009, 10:53 AM
#7
Le Mans Master
12-18-2009, 11:25 AM
#14
Burning Brakes
Well so far here is what I have planned:
Full ZR Widebody kit - In progress
New track oriented rotors
Spindle mount duct kit - In progress
New track pads
Z06 Bi mode mufflers with retro fit kit and muffler mod (My Borla Stingers will be for sale soon) - In progress
Pfadt Sway bars
Trickflow 225s
Meth injection
To see some progress pics and updates check my thread:
http://forums.corvetteforum.com/cana...lus-intro.html
Now that we are on Holidays I'll be getting a lot more done.
Full ZR Widebody kit - In progress
New track oriented rotors
Spindle mount duct kit - In progress
New track pads
Z06 Bi mode mufflers with retro fit kit and muffler mod (My Borla Stingers will be for sale soon) - In progress
Pfadt Sway bars
Trickflow 225s
Meth injection
To see some progress pics and updates check my thread:
http://forums.corvetteforum.com/cana...lus-intro.html
Now that we are on Holidays I'll be getting a lot more done.
Last edited by Spectrel; 12-18-2009 at 11:27 AM.
12-18-2009, 04:06 PM
#15
Drifting
12-18-2009, 04:31 PM
#16
Melting Slicks
Forged 402
New clutch (yet to be determined)
Flip drive
Upgraded fuel system
New shoes
*****....I can't wait Arun !!!!
New clutch (yet to be determined)
Flip drive
Upgraded fuel system
New shoes
*****....I can't wait Arun !!!!
Last edited by BUBBAS 01Z06; 12-18-2009 at 04:33 PM.
12-18-2009, 07:45 PM
#17
Racer
I'm gettings all the good stuff /parts for my H/C to be done in early spring, at Devon's P, shop . Just received my first box today springs , oil pump, some gaskets ,...injectors ,T chain and cam etc, to fallow also in the mail....Cant wait for spring to show up . Hope to run in HIGH 11th whit these new mods. Merry Xmas to all FORUM MEMBERS, hope you get lots of good C 5 stuff under the tree
12-18-2009, 08:15 PM
#18
Drifting
Member Since: Dec 2007
Location: aurora
Posts: 1,634
Likes: 0
Received 0 Likes
on
0 Posts
Block wet sanding buff and polish, new water pump, new speaker box install Sirius satellite radio, rebuild carb, not that this is modding but this is what i need to do. next years mod 502 ???? maybe.
Todd
Todd
12-18-2009, 09:27 PM
#20
Melting Slicks
Just finished installing an A&A S/C kit with a blower cam and valve train upgrades, melling oil pump, timing chain and Summitt SFI Pulley...
Clear corners with LED switchbacks
HID 6k fog's and low beams
Pfadt front sway bar
Hi Rise Hood & front cannards
Clear corners with LED switchbacks
HID 6k fog's and low beams
Pfadt front sway bar
Hi Rise Hood & front cannards