[Z06] Missing my beast :/ (CCW/Wide Fenders/BBK inside) c5 z06 pics
#1
Racer
Thread Starter
Missing my beast :/ (CCW/Wide Fenders/BBK inside) c5 z06 pics
Hope your enjoying it Drew! (Not sure if he made an account and is currently on corvetteforum but he spotted my car here)
As far as I know and from what John @ CCW told me, these were the first set on the c5z , oh and before anyone asks for specs:
19" CCW SP 500 Hybrid ( 19x10 front / 19x13 Rear ) 295/30/19 F / 345/30/19 R Toyo R888's
Stance coilovers ( they were great )
Corvette Creationz Wide rear fenders
C6 Z brake upgrade with stoptech drilled rotors
-Arbi
As far as I know and from what John @ CCW told me, these were the first set on the c5z , oh and before anyone asks for specs:
19" CCW SP 500 Hybrid ( 19x10 front / 19x13 Rear ) 295/30/19 F / 345/30/19 R Toyo R888's
Stance coilovers ( they were great )
Corvette Creationz Wide rear fenders
C6 Z brake upgrade with stoptech drilled rotors
-Arbi
The following 4 users liked this post by bizzmeister:
The following users liked this post:
bizzmeister (02-26-2017)
The following users liked this post:
bizzmeister (02-26-2017)
The following users liked this post:
bizzmeister (02-26-2017)
The following users liked this post:
bizzmeister (02-26-2017)
#6
Instructor
Very nice looking
Which settings did you use on your stance kit? And did you use any special camber settings to avoid tire rub on the rear fenders?
I´m in process installing the same setut with Stance/L5´s/CCW´s and would like to have a stance like yours.
The new owner has for sure bought a very clean and amazing looking Z
Which settings did you use on your stance kit? And did you use any special camber settings to avoid tire rub on the rear fenders?
I´m in process installing the same setut with Stance/L5´s/CCW´s and would like to have a stance like yours.
The new owner has for sure bought a very clean and amazing looking Z
The following users liked this post:
bizzmeister (02-26-2017)
#7
Racer
Thread Starter
Literally just a halltech venom intake, nothing else. Went big power on the previous car with minimal appearance mods, this time I wanted to go appearance / suspension first.
Thanks,
I did nothing special to the coilovers, It never rubbed. It only rubbed initially upon installing because it was way too low. But at the stance in the pictures above, never rubbed. Maybe just a tiny bit at full lock while turning but that's it.
Very nice looking
Which settings did you use on your stance kit? And did you use any special camber settings to avoid tire rub on the rear fenders?
I´m in process installing the same setut with Stance/L5´s/CCW´s and would like to have a stance like yours.
The new owner has for sure bought a very clean and amazing looking Z
Which settings did you use on your stance kit? And did you use any special camber settings to avoid tire rub on the rear fenders?
I´m in process installing the same setut with Stance/L5´s/CCW´s and would like to have a stance like yours.
The new owner has for sure bought a very clean and amazing looking Z
I did nothing special to the coilovers, It never rubbed. It only rubbed initially upon installing because it was way too low. But at the stance in the pictures above, never rubbed. Maybe just a tiny bit at full lock while turning but that's it.
The following users liked this post:
AndersT (02-27-2017)
The following users liked this post:
bizzmeister (03-08-2017)
#9
That's one very nice car. Sellers regret?
#11
Racer
Thread Starter
#12
#14
Wow, very well executed. Good job sir. Still enough fender gap for proper suspension travel and geometry, but ride height looks fantastic and dialed.
If you don't mind, how much did you pay for the fenders + install/prep + paint?
If you don't mind, how much did you pay for the fenders + install/prep + paint?
#16
Racer
Thread Starter
Lmao, good catch.
Thank you. I don't remember, I think it was around $450 for the fenders? I would never buy them again though because it was a total crap shoot and I lucky enough to pick out a set that was still lightly damaged compared to the rest of the stack of fenders.
I mean, they guy had to open literally 10 sets to find me a pair that was decent ( I mean without major cracks or breaks anywhere on there ) when I picked them up.
I paid nothing for install/prep/paint, father in law is a body guy.
Thanks!
I mean, they guy had to open literally 10 sets to find me a pair that was decent ( I mean without major cracks or breaks anywhere on there ) when I picked them up.
I paid nothing for install/prep/paint, father in law is a body guy.
Thanks!
#18
Nice. Very nice.
#19
Le Mans Master
Member Since: Jan 2000
Location: Georgetown TX
Posts: 8,435
Received 1,870 Likes
on
1,085 Posts
C5 of Year Finalist (appearance mods) 2019
Nice widebody. Love the CCW SP500 Hybrids. Just wish they would make those, in a 19x12" or 19x12.5" width.
Sad to see all these nice C5's being sold, not to be seen again here.
Sad to see all these nice C5's being sold, not to be seen again here.
#20
Just came across this thread on accident. I'm actually the current owner of these wheels As far as I can tell, this is still the only C5 set out there. I can't find anyone running them on a C6 or C7 either. Current owner of the car seemed like a good guy, but isn't on the forum that I know of. He's running satin black cup wheels, they look really good in person. I still need to drop the front another 0.25-0.5 inch, but finally got the rear sitting as far as it's going to go.
Last edited by heggsc5; 12-18-2019 at 05:05 AM.
The following users liked this post:
FYRARMS (12-18-2019)