Hub Stand Interest
04-06-2018, 10:17 PM
#1
Former Vendor
Thread Starter
Hub Stand Interest
I recently had a thread over the past week looking into making some hub stands. Due to the rules of the forum, the thread was removed because you must be a supporting vendor to gauge interest in a product. So nonetheless I am now a supporting vendor 
. Please continue the discussion we had in the past thread as it was very productive! I was able to get the quotes back from the machine shop and I'm looking at selling them right around the $700 area for a set of 4. I will be making a prototype set to test myself then move on to selling them! Continued feedback is greatly appreciated!
Thanks!
Colton
. Please continue the discussion we had in the past thread as it was very productive! I was able to get the quotes back from the machine shop and I'm looking at selling them right around the $700 area for a set of 4. I will be making a prototype set to test myself then move on to selling them! Continued feedback is greatly appreciated!Thanks!
Colton
04-07-2018, 04:09 AM
#2
Supporting Vendor
Member Since: Dec 2016
Location: Lookin over Hoover Dam
Posts: 3,513
Received 2,316 Likes
on
990 Posts
I'm in for 700.00 if they can match the pro set...you think you can pull that off?
Supporting vendor starts at like 375/mo doesn't it...you aint messin around here!
Supporting vendor starts at like 375/mo doesn't it...you aint messin around here!
Last edited by KnightDriveTV; 04-07-2018 at 04:10 AM.
!
The following users liked this post:
KnightDriveTV (04-09-2018)
The following users liked this post:
CSM Performance (04-09-2018)
The following users liked this post:
CSM Performance (04-09-2018)
The following users liked this post:
CSM Performance (04-09-2018)
The following users liked this post:
CSM Performance (04-09-2018)
04-09-2018, 10:14 PM
#8
Tech Contributor
Member Since: Oct 1999
Location: Charlotte, NC (formerly Endicott, NY)
Posts: 40,094
Received 8,928 Likes
on
5,333 Posts
Did you start the thread that was deleted as I think there is another hub stand thread missing that you might have posted in.
Bill
Bill
04-09-2018, 10:31 PM
#9
Former Vendor
Thread Starter
!
The following users liked this post:
CSM Performance (04-11-2018)
The following users liked this post:
CSM Performance (04-11-2018)
04-11-2018, 08:19 PM
#12
Burning Brakes
stands
I recently had a thread over the past week looking into making some hub stands. Due to the rules of the forum, the thread was removed because you must be a supporting vendor to gauge interest in a product. So nonetheless I am now a supporting vendor . Please continue the discussion we had in the past thread as it was very productive! I was able to get the quotes back from the machine shop and I'm looking at selling them right around the $700 area for a set of 4. I will be making a prototype set to test myself then move on to selling them! Continued feedback is greatly appreciated!
Thanks!
Colton
. Please continue the discussion we had in the past thread as it was very productive! I was able to get the quotes back from the machine shop and I'm looking at selling them right around the $700 area for a set of 4. I will be making a prototype set to test myself then move on to selling them! Continued feedback is greatly appreciated!Thanks!
Colton
The following users liked this post:
CSM Performance (04-11-2018)
04-11-2018, 10:56 PM
#13
Former Vendor
Thread Starter
We got the website up and going! If you would like to get email updates of our progress (we will not spam you) please visit us at: https://csmperformance.com/ and signup at the bottom right of the page!
Much Appreciated!
CSM Performance
Much Appreciated!
CSM Performance
The following users liked this post:
CSM Performance (04-16-2018)
The following users liked this post:
CSM Performance (04-16-2018)
The following users liked this post:
CSM Performance (04-16-2018)
04-16-2018, 11:16 AM
#17
Former Vendor
Thread Starter
Update:
We finished up the prototype this weekend. I am waiting for one more component to come in and then we will go into testing! Stay Tuned!
We finished up the prototype this weekend. I am waiting for one more component to come in and then we will go into testing! Stay Tuned!
