My 1958 restomod
#21
Advanced
Thread Starter
#22
Advanced
Thread Starter
#23
Melting Slicks
Member Since: Feb 2011
Location: Middletown Ohio
Posts: 2,892
Received 167 Likes
on
130 Posts
2016 C1 of Year Finalist
Excellent car!
Nice mods but not over the top like some.
Actually I like the picture with the wide whites and rally wheels on the car...
Nice mods but not over the top like some.
Actually I like the picture with the wide whites and rally wheels on the car...
Last edited by ohiovet; 12-14-2015 at 10:09 AM.
The following users liked this post:
Ironduke01 (12-14-2015)
#24
Team Owner
Member Since: Oct 2004
Location: altered state
Posts: 81,242
Received 3,043 Likes
on
2,602 Posts
St. Jude Donor '05
Jerry Noone who did the work
I used to work few bays down from him when he had a small shop in Simi Valley circa late 80s? Tried helping me straighten my then 67 rs camaro out. Hes always done super clean work nice guy too
Car looks good
Last edited by cv67; 12-14-2015 at 10:20 AM.
The following users liked this post:
Ironduke01 (12-14-2015)
#25
Advanced
Thread Starter
The following users liked this post:
Ironduke01 (12-14-2015)
#28
[QUOTE=Ironduke01;1591108758]I actually have a set of 15" wheels and reproduction wheel covers for the car. I used Goodrich Silvertown wide white wall radials. I don't have a picture of the car with these, but below is the design drawing. It looks dead stock when we have them on. I also included a picture of the car being built with these wheels on it.
While I really like the current wheels on the car, I lean towards the whitewalls and reproduction covers because it is more stock looking.
The car is gorgeous! Enjoy!
While I really like the current wheels on the car, I lean towards the whitewalls and reproduction covers because it is more stock looking.
The car is gorgeous! Enjoy!
The following 2 users liked this post by sbaba:
Ironcross (12-17-2015),
Ironduke01 (12-16-2015)
#30
Melting Slicks
Darn...I "just now" caught the significance of the information on the glove compartment clearance.
Your arm rest compartment pivots "FORWARD"...which eliminates clearance problems when it tilts backward. Great..!!
Thanks...Stan
Last edited by Stan's Customs; 12-16-2015 at 01:23 PM.
#31
Melting Slicks
Member Since: Jul 2010
Location: Between Tally and Gatorville ,Florida
Posts: 3,454
Received 83 Likes
on
69 Posts
Didn't think so but, thought I ask. I know there was a vendor a few years back offering one. I'm going to install a center console on my 62 build. Guess I will end up building it as well. love the way the front section is tilt
#32
Advanced
Thread Starter
#34
Racer
Member Since: Jan 2006
Location: Excelsior Springs, MO
Posts: 279
Received 158 Likes
on
75 Posts
2023 Corvette of the Year Finalist - Modified
2022 C1 of the Year Winner - Modified
C1 of Year Finalist (performance mods) 2019
WOW... love the radio speaker too.
I may re-do my console and dash... I have a C5 Shifter, but have installed an automatic shifter that looks like the stock one. I also have been trying to figure out cup holders - this is the best looking setup I've seen.
I've got C5 brakes on my 61 with C4 front & rear suspension - I run 17" American Maverick wheels to clear the brakes. I told my Wife they don't make large white walls for 17" wheels.... she quickly found a set at Cokers...
on the internet. We are still pending on them....
I've got C5 brakes on my 61 with C4 front & rear suspension - I run 17" American Maverick wheels to clear the brakes. I told my Wife they don't make large white walls for 17" wheels.... she quickly found a set at Cokers...
on the internet. We are still pending on them....
Last edited by ironheadvette; 12-30-2015 at 09:36 PM. Reason: added info
#36
Advanced
Thread Starter
I may re-do my console and dash... I have a C5 Shifter, but have installed an automatic shifter that looks like the stock one. I also have been trying to figure out cup holders - this is the best looking setup I've seen.
I've got C5 brakes on my 61 with C4 front & rear suspension - I run 17" American Maverick wheels to clear the brakes. I told my Wife they don't make large white walls for 17" wheels.... she quickly found a set at Cokers...
on the internet. We are still pending on them....
I've got C5 brakes on my 61 with C4 front & rear suspension - I run 17" American Maverick wheels to clear the brakes. I told my Wife they don't make large white walls for 17" wheels.... she quickly found a set at Cokers...
on the internet. We are still pending on them....
#37
Advanced
Thread Starter
I may re-do my console and dash... I have a C5 Shifter, but have installed an automatic shifter that looks like the stock one. I also have been trying to figure out cup holders - this is the best looking setup I've seen.
I've got C5 brakes on my 61 with C4 front & rear suspension - I run 17" American Maverick wheels to clear the brakes. I told my Wife they don't make large white walls for 17" wheels.... she quickly found a set at Cokers...
on the internet. We are still pending on them....
I've got C5 brakes on my 61 with C4 front & rear suspension - I run 17" American Maverick wheels to clear the brakes. I told my Wife they don't make large white walls for 17" wheels.... she quickly found a set at Cokers...
on the internet. We are still pending on them....
#38
Melting Slicks
#39
Melting Slicks
Highhh dollar stuff..nice!
The following users liked this post:
Ironduke01 (12-31-2015)
The following users liked this post:
Ironduke01 (12-31-2015)