C-2 4 speed transmissions For Sale
#1
Former Vendor
Thread Starter
C-2 4 speed transmissions For Sale
Make offer--All with correct cases, tail housings, side covers, stampings, etc.
1) SOLD--- 1964 ----Dated April 8, 1964 -----M 20-----$750.00 OBO---SOLD
2) sold—1967 ----P7A09-- (Jan. 9, 1967) ------M20------$650.00 OBO
3) 1967 sold--P7C13-- (March 13, 1967)---M21------$700.00 OBO
Sold—-4) 1965-----P0630-- (June 30, 1965)----M20------$700.00 OBO—sold
Detailed photos and all numbers/codes available.
Have some bell housings, flywheels, cross shafts, drive shafts, brackets/braces, and shifters/linkage.
Please e me at geopar@gvtc.com
Thanks,
George
210 748 4693
All sold
1) SOLD--- 1964 ----Dated April 8, 1964 -----M 20-----$750.00 OBO---SOLD
2) sold—1967 ----P7A09-- (Jan. 9, 1967) ------M20------$650.00 OBO
3) 1967 sold--P7C13-- (March 13, 1967)---M21------$700.00 OBO
Sold—-4) 1965-----P0630-- (June 30, 1965)----M20------$700.00 OBO—sold
Detailed photos and all numbers/codes available.
Have some bell housings, flywheels, cross shafts, drive shafts, brackets/braces, and shifters/linkage.
Please e me at geopar@gvtc.com
Thanks,
George
210 748 4693
All sold
Last edited by Corvettes by George; 03-03-2018 at 08:30 AM.
#3
Former Vendor
Thread Starter
I have a nice 4 speed from a 1960 corvette.
Have original shifter/linkage, aluminum bellhousing, rear mount bracket, maybe a good clutch assembly, and most of the z bar/linkage pieces for your conversion.
Do not have a clutch pedal assembly.
E me at geopar@gvtc.com
George
210-748-4693
Have original shifter/linkage, aluminum bellhousing, rear mount bracket, maybe a good clutch assembly, and most of the z bar/linkage pieces for your conversion.
Do not have a clutch pedal assembly.
E me at geopar@gvtc.com
George
210-748-4693
#7
Former Vendor
Thread Starter
Good transmissions here, and I thought good prices?
Shifters, linkage, brackets, braces.
Drive shafts, yokes, Z bars, switches, etc.
Would like to move these .
George
geopar@gvtc.com
210 748 4693
Shifters, linkage, brackets, braces.
Drive shafts, yokes, Z bars, switches, etc.
Would like to move these .
George
geopar@gvtc.com
210 748 4693
#9
Former Vendor
Thread Starter
All transmissions are in good working order.
All of these pulled in favor of 5 speed installation.
G
geopar@gvtc.com
210 748 4693
All of these pulled in favor of 5 speed installation.
G
geopar@gvtc.com
210 748 4693
#10
Racer
Transmissions
I am looking for a early 63 hurst short bent shaft shifter for a Borg Warner. Need linkage too. Can you help? Dave 864-380-4796 or dcrocker316@gmail.com
#11
Former Vendor
Thread Starter
I am looking for a early 63 hurst short bent shaft shifter for a Borg Warner. Need linkage too. Can you help? Dave 864-380-4796 or dcrocker316@gmail.com
G
#13
I put a 4 speed in my 59, be very carefull when you weld the Brkt to the frame. Measure 3 times & weld once.
Michael
#14
Drifting
Tri power
George, I see a tri-power intake w/carbs in one of your pics. is that for a big block chevy if so how much you asking, also I may need a complete 4spd. set-up for a 67 corvette s/b with an automatic I want to convert.
Thanks
Chalie
Chalie55@comcast.net
Thanks
Chalie
Chalie55@comcast.net
#15
Former Vendor
Thread Starter
George, I see a tri-power intake w/carbs in one of your pics. is that for a big block chevy if so how much you asking, also I may need a complete 4spd. set-up for a 67 corvette s/b with an automatic I want to convert.
Thanks
Chalie
Chalie55@comcast.net
Thanks
Chalie
Chalie55@comcast.net
I have an "097" square port 3 x 2 for sale---$1,200.00 (no carbs).
I should have everything for a 4 speed changeover except the pedal assembly (unless a pedal assembly from a '68 will fit?)
geopar@gvtc.com