Parts leftover from '60 restoration
04-07-2013, 07:57 PM
#22
An original 283 dipstick is 19-9/16" from the circular metal stop just below finger hole to the FULL line; 20-1/2" from the circular stop tap to the ADD line and 3/4" between FULL and ADD. The ADD and FULL are overstamped so that you can see both words on the back side. A capital "W" will be stamped between the finger hole and the circular stop or a couple of inches below the stop disk.
Do you have one of these dipsticks?
Do you have one of these dipsticks?
04-10-2013, 08:08 AM
#23
Former Vendor
Thread Starter
An original 283 dipstick is 19-9/16" from the circular metal stop just below finger hole to the FULL line; 20-1/2" from the circular stop tap to the ADD line and 3/4" between FULL and ADD. The ADD and FULL are overstamped so that you can see both words on the back side. A capital "W" will be stamped between the finger hole and the circular stop or a couple of inches below the stop disk.
Do you have one of these dipsticks?
Do you have one of these dipsticks?
G.
04-14-2013, 08:29 PM
#24
I am looking for stamped steel (not stainless) accelerator return spring bracket that mounts on the top of the thermostat cover.
Clutch head screws to mount the grab bar to brackets?
Original, steel wire covers that are located between the door threshold and the side of the seat, under the carpet. They are usually rusted out.
Do you have any original bolts or screws that you did not reuse?
Clutch head screws to mount the grab bar to brackets?
Original, steel wire covers that are located between the door threshold and the side of the seat, under the carpet. They are usually rusted out.
Do you have any original bolts or screws that you did not reuse?
04-16-2013, 10:31 AM
#26
Former Vendor
Thread Starter
Hi Ben,
I have a nice set of rear springs and the forward hangers/bolts.
Send me an e message for photos/dates/pricing.
George
210 748 4603
geopar@gvtc.com
I have a nice set of rear springs and the forward hangers/bolts.
Send me an e message for photos/dates/pricing.
George
210 748 4603
geopar@gvtc.com
04-16-2013, 04:41 PM
#27
Pro
Moulding
I am interested in the upper windshield stainless moulding and channel that is pictured with the group of stainless trim,,Do you still have it,,if so how much ? I also sent a PM about it,,
04-17-2013, 09:12 AM
#28
Former Vendor
Thread Starter
I think the molding and channel is for the lower inside windshield?
G
geopar@gvtc.com
04-17-2013, 01:12 PM
#29
Pro
moulding
If you look at the picture here in you thread,,The very first moulding and channel that is on the folding stand is an upper stainless and channel,,then the next piece is the lower,,the upper is what I am looking at,,I s it still available ?
04-17-2013, 01:25 PM
#30
Former Vendor
Thread Starter
Yes, I do have those two pieces of the windshield frame.
E mail or PM me for more photos/description/pricing.
Thanks,
George
geopar@gvtc.com
210 748 4693
04-17-2013, 08:49 PM
#32
Former Vendor
Thread Starter
05-04-2013, 01:02 AM
#36
I'd be interested in a pair of the front bumper brackets. the long ones ones that bolt directly to the frame at the top of your picture. I need a good straight pair, not all pitted up. You seem to have a number of pairs. I tried messaging you but no answer...
07-25-2013, 01:41 PM
#40
Instructor
George,
You were going to get back to me with a total shipped price for the rear deck latches and front Ebrake cable. Also, do you have a pair of the top window stop brackets with screw? all for '62.
Skip
You were going to get back to me with a total shipped price for the rear deck latches and front Ebrake cable. Also, do you have a pair of the top window stop brackets with screw? all for '62.
Skip
