need tips on cutting gauge bezel to fit CD player
#1
Intermediate
Thread Starter
Member Since: Jan 2004
Location: Winnipeg MB
Posts: 34
Likes: 0
Received 0 Likes
on
0 Posts
need tips on cutting gauge bezel to fit CD player
On my 70, I want to install a new CD player into the location where the stock radio sits. I see they make a repo bezel that is moulded to fit the new DIN radios, but they want 225 bucks. A normal repo bezel is only 75 bucks.
Who has cut the stock bezel to install a CD?
How can I trim the hole to make it look nice?
Any experience in this conversion is appreciated.
Who has cut the stock bezel to install a CD?
How can I trim the hole to make it look nice?
Any experience in this conversion is appreciated.
#4
Melting Slicks
Member Since: May 1999
Location: Moon Township PA
Posts: 2,897
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by marley
On my 70, I want to install a new CD player into the location where the stock radio sits. I see they make a repo bezel that is moulded to fit the new DIN radios, but they want 225 bucks. A normal repo bezel is only 75 bucks.
Who has cut the stock bezel to install a CD?
How can I trim the hole to make it look nice?
Any experience in this conversion is appreciated.
Who has cut the stock bezel to install a CD?
How can I trim the hole to make it look nice?
Any experience in this conversion is appreciated.
Just my $.02.
Gary
#5
Racer
Member Since: Dec 2003
Location: Pasadena Maryland
Posts: 304
Likes: 0
Received 0 Likes
on
0 Posts
with GaryS. Don't cut the original. I've had my Vette since 1995 and it still has the original 8 track unit in it. The radio works fine but the 8track is just there for looks. I think I can count on one hand how many times I've turned on the radio. Couldn't hear it if I wanted to.
#7
Advanced
Member Since: Jan 2005
Location: Aylesbury Buckinghamshire. UK
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
I bought a new bezel for my 80 and enlarged the hole to fit a new Sony CD player. The front fascia of the player was slightly larger than the main body of the unit therefore once fitted the rough edges were hidden by the fascia........looks the business.
#8
Le Mans Master
Member Since: Feb 1999
Location: Hoosier
Posts: 6,807
Likes: 0
Received 0 Likes
on
0 Posts
Cruise-In III Veteran
Originally Posted by GaryS
Whatever you do, cut a repro unit and not your original. Original center bezels require a mortgage and your first born male child as collateral. So many of them are butchered by folks trying to add aftermarket radios or break during removal that they are scarce. If you ever want to restore your car to original, you will be happy that you have the original and unmolested center piece.
Just my $.02.
Gary
Just my $.02.
Gary
#9
Le Mans Master
Member Since: Feb 1999
Location: Hoosier
Posts: 6,807
Likes: 0
Received 0 Likes
on
0 Posts
Cruise-In III Veteran
This is a reprod bezel. I cut out the gauge and radio surface and molded in a sized/fitted sheet of aluminum. Even had the opportunity to add a 6th gauge.
#11
Drifting
Member Since: Mar 2001
Location: Valencia (near LA) CA
Posts: 1,600
Likes: 0
Received 0 Likes
on
0 Posts
At one point in time I wanted to install a modern head unit in my '68. I didn't want to cut origional bezel. I called a Corvette junk yard and they had a used bezel that was already cut for $50
~Jay
~Jay
#12
Safety Car
As far as buying a new one to cut or cutting your old one is up to you. I didn't have any reservations about cutting the bezel in my 75. I figure it's about as likely someone would want the old AM/FM as someone would want to put bias ply tires back on.
Anyway the job really isn't too tough. I bought the $10 adaptor bracket from millionbuy and traced around the square so I knew where to cut. Then I used my $20 4 1/2" angle grinder with a cutting blade to do most of the cutting. I finished cutting the corners with a dremel and a file. Everything fits and works great. I did all this with the bezel still hooked up to the guages. (You have to remove the bezel from the console though). The whole job to a little over an hour and was one of the best things I've done so far. I believe Redwingvette has done something similar.
Anyway the job really isn't too tough. I bought the $10 adaptor bracket from millionbuy and traced around the square so I knew where to cut. Then I used my $20 4 1/2" angle grinder with a cutting blade to do most of the cutting. I finished cutting the corners with a dremel and a file. Everything fits and works great. I did all this with the bezel still hooked up to the guages. (You have to remove the bezel from the console though). The whole job to a little over an hour and was one of the best things I've done so far. I believe Redwingvette has done something similar.
#13
Racer
Member Since: Jan 2004
Location: Thomasville Ga
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
I did my 71...but, like what's been mentioned above I bought a repro and saved the original.
Here's the trim piece you need to buy:
Here's the back of it:
Here's the bezel cut with a dremel:
Here's the cut bezel with the stereo(minus the faceplate) mounted in the trim piece:
Here's the trim, stereo, and bezel from the side:
[/IMG]http://memimage.cardomain.net/member_images/10/web/586000-586999/586584_23_full.jpg[/IMG]
Here's the final product:
Here's the trim piece you need to buy:
Here's the back of it:
Here's the bezel cut with a dremel:
Here's the cut bezel with the stereo(minus the faceplate) mounted in the trim piece:
Here's the trim, stereo, and bezel from the side:
[/IMG]http://memimage.cardomain.net/member_images/10/web/586000-586999/586584_23_full.jpg[/IMG]
Here's the final product:
Last edited by fjetb; 11-21-2005 at 09:20 PM.
#14
Melting Slicks
Originally Posted by fotyfobravo
i used a dremel and a file for the final fit
Last edited by rosslato; 11-21-2005 at 10:20 PM. Reason: wrong pic
#18
Instructor
Member Since: Jun 2005
Location: Rochester MN
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
on a similar note, I've been trying to hunt down an original radio for my 79. When they sell on ebay they always end up over $100. Any other places I should be looking to get it back to the original look? (I never turn on the cheap sony aftermarket anyway)
#20
Safety Car
Member Since: Dec 2004
Location: Jersey Shore Exit 98
Posts: 4,876
Likes: 0
Received 0 Likes
on
0 Posts
Original Bezel
Originally Posted by marley
On my 70, I want to install a new CD player into the location where the stock radio sits. I see they make a repo bezel that is moulded to fit the new DIN radios, but they want 225 bucks. A normal repo bezel is only 75 bucks.
Who has cut the stock bezel to install a CD?
How can I trim the hole to make it look nice?
Any experience in this conversion is appreciated.
Who has cut the stock bezel to install a CD?
How can I trim the hole to make it look nice?
Any experience in this conversion is appreciated.
First tape off the area where the new CD player will go. Put the new trim piece on the bezel over the tape and draw w/a sharpie inside the trim. Next take away the trim piece and use the razor to cut into the line on the tape. Make sure before you cut the the opening is level & square. After you cut along the line w/the razor take the new saw blade (glove is required) and cut slowly along the line.
Remove tape and install. Send me a PM w/your e-mail address & I'll send you a pic of how my turned out.