Torq Thrust II - Pics to Share on Car?
#162
Thank you, both set ups do the car justice.
Dave
Dave
Here is a side shot of the car still with the 17s on back, and 16s on the front. It’s now a little over an inch taller and wider all around now with the 18/17 inch combo (27 inch tall front, 28.25 tall rear). The Nitto Invo 255/50r17s that were on the rear seemed to stick pretty well most of the time, and would do perfectly fine with a stock to mild build, but I have a 400 wheel hp LS swap with the T56 trans and 3.73 gears, so I really wanted some more traction.
The following users liked this post:
SHIFT A (12-12-2017)
#164
Safety Car
The following users liked this post:
JBrooke825 (12-12-2017)
#165
Advanced
Those fit and look great. If you you get 4.5 inch backspace on an 8 inch wide wheel they will tuck into the fender 1/2 inch more, and might look a little funky in my opinion.
Also, there are not many tire options for 16 inch wheels, so you should really look up tire sizes before you decide on wheels. 15 inch wheels, and then 17 and 18 inch wheels have a lot more options to match the OEM tire sizes or bigger.
#171
That blue Corvette picture posted by Jclgodale3 really IS perfection isn't it ? ! ? ! Would anyone know where to buy a set of those replacement headlights?
Last edited by Team Evil; 12-15-2017 at 08:53 PM.
#172
Racer
17x8 All around with Nitto 255/50zR17 give me a 27.1 inch diameter .... no mods have been done to suspension yet..and I did not have to remove EBrake bracket.
#174
Dementer sole survivor
Member Since: Oct 2015
Location: YUPPY HELL Westford MASS
Posts: 16,432
Received 6,278 Likes
on
3,915 Posts
2020 C3 of the Year Finalist - Modified
2020 Corvette of the Year Finalist (performance mods)
2019 C3 of Year Winner (performance mods)
2016 C3 of Year Finalist
some better angles on my 235/55/17 with torque thrust II
Last edited by Rescue Rogers; 09-26-2018 at 08:44 PM.
#175
Racer
Where did you get the red stripe on the rims?
#176
Racer
18x10s all around with 285/35R18 tires. Torq Thrust II in gray. 5.6" back spacing if I remember right. I have small spacers (10mm I think?) because the rears were very close to the frame and would occasionally rub. Offset trailing arms as well.
Last edited by supervette64; 09-26-2018 at 08:55 PM.
#177
Dementer sole survivor
Member Since: Oct 2015
Location: YUPPY HELL Westford MASS
Posts: 16,432
Received 6,278 Likes
on
3,915 Posts
2020 C3 of the Year Finalist - Modified
2020 Corvette of the Year Finalist (performance mods)
2019 C3 of Year Winner (performance mods)
2016 C3 of Year Finalist
theyre called rim savers. They're supposed to protect from curb rash but they give that red line look. They're also available in other colors.
https://www.rimbladesusa.com/product/rimsavers/
I like them. The first rim I did looks okay but the 4rth rim I did looks perfect. Really easy to apply and they stay on really well. A cheaper way to get that look.
heres some close ups
Stayed on during a blow out and survived the old tire coming off and being replaced. I have a replacement strip but havent needed to put it on yet
https://www.rimbladesusa.com/product/rimsavers/
I like them. The first rim I did looks okay but the 4rth rim I did looks perfect. Really easy to apply and they stay on really well. A cheaper way to get that look.
heres some close ups
Stayed on during a blow out and survived the old tire coming off and being replaced. I have a replacement strip but havent needed to put it on yet
Last edited by Rescue Rogers; 09-26-2018 at 09:13 PM.
#178
Dementer sole survivor
Member Since: Oct 2015
Location: YUPPY HELL Westford MASS
Posts: 16,432
Received 6,278 Likes
on
3,915 Posts
2020 C3 of the Year Finalist - Modified
2020 Corvette of the Year Finalist (performance mods)
2019 C3 of Year Winner (performance mods)
2016 C3 of Year Finalist
Thats a sweet vette you got there. Looks like your using VB&P suspension. I picked some up this past spring, hoping to install it this winter. I hope my car looks as nice as yours does
#179
Racer
Its too bad VB&P went out of business, pretty happy with the suspension so far. If you have any questions with it feel free to send me a message (since you can't call them anymore).
#180
Dementer sole survivor
Member Since: Oct 2015
Location: YUPPY HELL Westford MASS
Posts: 16,432
Received 6,278 Likes
on
3,915 Posts
2020 C3 of the Year Finalist - Modified
2020 Corvette of the Year Finalist (performance mods)
2019 C3 of Year Winner (performance mods)
2016 C3 of Year Finalist
Thanks! My buddy John has them too, thats why I grabbed them when I could. Hes given me the directions and made me the reinforcement discs as well. Hopefully I dont run into any problems........I'll start a winter projects thread here in a couple of weeks.
PS I stole the rimsavers idea from another forum member here a couple of years ago. I really like them alot
PS I stole the rimsavers idea from another forum member here a couple of years ago. I really like them alot