71 L-88 Replica (kinda)
#261
Safety Car
Going good.
Busy with all sorts of stuff.... working on an LT1 heads and cam/4L60E side project that's going in an 84 for a local guy, my race car burned a few pistons last race, then my 92 torched the elect waterpump on the way to work last week.... waiting on parts to fix both of mine.
After seeing a nice looking 69 L46 go pretty cheap before I could make up my mind.... I decided last week that I need a chrome bumper driver... I just finished getting my money in order so it doesn't happen again and I'm just getting ready to run a few leads on some semi-local cars down.
Yours is looking great. Its gonna be an awesome ride when you're done.
Will
Busy with all sorts of stuff.... working on an LT1 heads and cam/4L60E side project that's going in an 84 for a local guy, my race car burned a few pistons last race, then my 92 torched the elect waterpump on the way to work last week.... waiting on parts to fix both of mine.
After seeing a nice looking 69 L46 go pretty cheap before I could make up my mind.... I decided last week that I need a chrome bumper driver... I just finished getting my money in order so it doesn't happen again and I'm just getting ready to run a few leads on some semi-local cars down.
Yours is looking great. Its gonna be an awesome ride when you're done.
Will
#262
#263
Melting Slicks
Thread Starter
#264
#265
Melting Slicks
Thread Starter
Have not been idle but slow. I have started on the dash, I have the engine harness wired, I am waiting for a Stainless Steel fuel line to arrive which will go under the car, I am almost done with the trans tunnel so it will be time to wire. I am going with American auto wires 22 circuit kit and another decision is I plan on using Kore3 C6 Z51 caliber and rotors for the front vice the C4. I got my headers and side pipes back from Jet hot and they came out great.
The following users liked this post:
MISTERZ06 (05-25-2017)
The following users liked this post:
MISTERZ06 (05-25-2017)
#268
Have not been idle but slow. I have started on the dash, I have the engine harness wired, I am waiting for a Stainless Steel fuel line to arrive which will go under the car, I am almost done with the trans tunnel so it will be time to wire. I am going with American auto wires 22 circuit kit and another decision is I plan on using Kore3 C6 Z51 caliber and rotors for the front vice the C4. I got my headers and side pipes back from Jet hot and they came out great.
#270
Melting Slicks
Thread Starter
The headers are Stahl Headers which Advance Composite Products now makes them. The fabricator from Stahl (Greg) now works for ACP and does a beautiful job. Mine are 1 7/8ths stepped to 2". The side pipes I made from 3 1/2" tube and I will use sweet thunders large insert which I used once before and was very pleased.
Note ACP has all of Stahls jigs and has added a few more.
Note ACP has all of Stahls jigs and has added a few more.
#271
Drifting
The headers are Stahl Headers which Advance Composite Products now makes them. The fabricator from Stahl (Greg) now works for ACP and does a beautiful job. Mine are 1 7/8ths stepped to 2". The side pipes I made from 3 1/2" tube and I will use sweet thunders large insert which I used once before and was very pleased.
Note ACP has all of Stahls jigs and has added a few more.
Note ACP has all of Stahls jigs and has added a few more.
#272
Melting Slicks
Thread Starter
#273
The headers are Stahl Headers which Advance Composite Products now makes them. The fabricator from Stahl (Greg) now works for ACP and does a beautiful job. Mine are 1 7/8ths stepped to 2". The side pipes I made from 3 1/2" tube and I will use sweet thunders large insert which I used once before and was very pleased.
Note ACP has all of Stahls jigs and has added a few more.
Note ACP has all of Stahls jigs and has added a few more.
#276
Melting Slicks
Thread Starter
#278
Burning Brakes
trim-less t-tops
vstol, after reading your comments in rvzio's thread I went back and looked at your trim-less t-tops on the previous page. I like it! Any close-up pictures of those t-top edges? Thx, -R
#279
Melting Slicks
Thread Starter