How do you keep the C3 from getting light above 120mph?
#61
Team Owner
:
I'm out at willow springs raceway....
So, to vent or not to vent, that is the question..
So let me get this right.. We seal the hell out of the radiator to prevent from overheating.... But doing this gives us more lift..... Dam if you do, dam if ya don't .. At lest it seems
I'm out at willow springs raceway....
So, to vent or not to vent, that is the question..
So let me get this right.. We seal the hell out of the radiator to prevent from overheating.... But doing this gives us more lift..... Dam if you do, dam if ya don't .. At lest it seems
So the curiosity is, with a stock fan shroud, the air is redirected horizontally into the front of the engine, no matter the fan being electric or mechanical....but I have dual spals, mounted to the lower and upper rad U channels, so fans are parallel to the radiator...and direct the air down and under , no matter if fans are on or not....the air is aimed at the harmonica balancer...
which is why there is no pressure under the hood on the ENGINE side of the radiator, on MY car...
IF I remove the gasket and let that incoming air up and over, I wonder about cooling at moderate speeds, with all the pressure relieved the air is not forced through the radiator, ....can't win...
#63
Le Mans Master
Fact is, at the most basic level this whole issue is one of aerodynamic pressure differentials. Since we're dealing with a body in ground effect rather than one in free air, generally the less air is allowed under the nose relative to that flowing above it, the easier it is to generate downforce rather than lift at speed. Among other things, unless vented elsewhere so as to divert it from ultimately ending up beneath the nose of the car, radiator exit flow adversely affects pressure differentials towards or into the lift side of the equation.
At speed, aero becomes a first order factor. That isn't really a concern worth stressing over for the vast majority of owners. But, when approaching the upper end of the performance scale, until and unless substantial supporting data clearly shows otherwise for a given vehicle, best IMCO to accept conventional wisdom (as has been established by engineers in the field) and seek to adapt proven methods for managing aerodynamics per those norms.
vette427-sbc, I've been wondering how long it would take someone to bring up that type of C3 hood extraction.
At speed, aero becomes a first order factor. That isn't really a concern worth stressing over for the vast majority of owners. But, when approaching the upper end of the performance scale, until and unless substantial supporting data clearly shows otherwise for a given vehicle, best IMCO to accept conventional wisdom (as has been established by engineers in the field) and seek to adapt proven methods for managing aerodynamics per those norms.
vette427-sbc, I've been wondering how long it would take someone to bring up that type of C3 hood extraction.
Last edited by TheSkunkWorks; 05-06-2012 at 09:23 PM.
#64
Tech Contributor
Member Since: Jun 2004
Location: I tend to be leery of any guy who doesn't own a chainsaw or a handgun.
Posts: 18,350
Received 767 Likes
on
549 Posts
I can't perceive any lift or "steering getting light" issues on my '69. The current configuration is pretty simple, but have a couple additional tweaks planned. I've got the ride height down an inch or so from the stock height. I've got a Pace Car spoiler that helps divert a portion of the air from getting underneath the car, and I've blocked off the two grills (in front of the headlights) to reduce the volume of air entering the pre-radiator plenum. The car never overheats (I credit a good engine tune and a DeWitt radiator), even on 90* track days (like last week) or 100* track days (like last July). I may try to block off some of the center grill too.
I've been working on some aluminum panels to smooth the bottom of the car (particularly in the front before the air gets hopelessly turbulent) and other panels to help direct the air out the side gills instead of letting it collect under the car. Once I get this finished I need to do some wool tuft testing to see if it would be productive to lower the bottom edge of the underdoor rocker moldings. If it looks like air is actually trying to enter the underside of the car (from the sides) some of this air could be blocked by extending the molding lower edge downward. It looks like an additional two inch drop would be almost visually unnoticeable.
I've been working on some aluminum panels to smooth the bottom of the car (particularly in the front before the air gets hopelessly turbulent) and other panels to help direct the air out the side gills instead of letting it collect under the car. Once I get this finished I need to do some wool tuft testing to see if it would be productive to lower the bottom edge of the underdoor rocker moldings. If it looks like air is actually trying to enter the underside of the car (from the sides) some of this air could be blocked by extending the molding lower edge downward. It looks like an additional two inch drop would be almost visually unnoticeable.
#65
Le Mans Master
Sounds like you have a good working plan.
IIRC, Bee Jay experimented at one time with some sheet metal block-off plates behind his grilles without detriment to temps (also has PC dam). I'd think you could keep reducing the inlet area as long as they're OK. Yep, this one's on my list too.
And, side skirts wouldn't seem too hard a project, as long as you can verify they'd be working in your favor at speed.
With my '78 having been off the ground for a while, I've spent more than a few hours underneath it contemplating how to go about the whole splitter/pan/diffuser thing. I've actually found a resource for doing the splitters to my specs, and have started working on the station bucks for molding a prototype diffuser, but just don't have the funds to get either to the finish line just now. Same story with other somewhat hardcore bits I'd like to develop for market...
IIRC, Bee Jay experimented at one time with some sheet metal block-off plates behind his grilles without detriment to temps (also has PC dam). I'd think you could keep reducing the inlet area as long as they're OK. Yep, this one's on my list too.
And, side skirts wouldn't seem too hard a project, as long as you can verify they'd be working in your favor at speed.
With my '78 having been off the ground for a while, I've spent more than a few hours underneath it contemplating how to go about the whole splitter/pan/diffuser thing. I've actually found a resource for doing the splitters to my specs, and have started working on the station bucks for molding a prototype diffuser, but just don't have the funds to get either to the finish line just now. Same story with other somewhat hardcore bits I'd like to develop for market...
#66
#67
Team Owner
Member Since: Oct 2004
Location: Springfield MO
Posts: 23,831
Likes: 0
Received 6 Likes
on
6 Posts
St. Jude Donor '07
I've said it before, but I've always been amazed at how much difference even the little stock chin spoiler makes on my 77. It used to start to get noticeably (and frighteningly) light in front even at higher highway speeds. In the 60-70mph range.
#68
Drifting
I doubt if the stock 'gills' on thier own would allow enough extract air flow to balance air coming in to engine compartment - perhaps removal and adapation of the area where the 'fillet' sheet metal covers over the frame (at rear of engine compartment adjacent to bulkhead/behind wheel tubs) ?
#69
Le Mans Master
I doubt if the stock 'gills' on thier own would allow enough extract air flow to balance air coming in to engine compartment - perhaps removal and adapation of the area where the 'fillet' sheet metal covers over the frame (at rear of engine compartment adjacent to bulkhead/behind wheel tubs) ?
Last edited by TheSkunkWorks; 05-07-2012 at 03:30 PM.
#71
Burning Brakes
...
With my '78 having been off the ground for a while, I've spent more than a few hours underneath it contemplating how to go about the whole splitter/pan/diffuser thing. I've actually found a resource for doing the splitters to my specs, and have started working on the station bucks for molding a prototype diffuser, but just don't have the funds to get either to the finish line just now. Same story with other somewhat hardcore bits I'd like to develop for market...
With my '78 having been off the ground for a while, I've spent more than a few hours underneath it contemplating how to go about the whole splitter/pan/diffuser thing. I've actually found a resource for doing the splitters to my specs, and have started working on the station bucks for molding a prototype diffuser, but just don't have the funds to get either to the finish line just now. Same story with other somewhat hardcore bits I'd like to develop for market...
Not sure if I posted pics of mine on this site but heres one. The rear "parachute" is probably horrible for high speed aero
#74
Race Director
Thread Starter
Made a cool mod for this.... and I agree with you on this..
Took out the tire, and put springs in the bolts, the springs hold the carrier down, but if hit will allow it to move up...
#75
Burning Brakes
What about opening the L88 style hood where I have marked in pencil? I realize getting the air out of the engine compartment is all about air pressure, my thought is that the air being diverted up and over this area of the hood would create a low pressure area helping pull air out of the engine bay. Putting the openings here move them to a location that's behind the radiator (though not much, still should pull some hot air) as compared to opening up the vertical area just forward of what's marked. Waste of time, effort and energy?
#76
Tech Contributor
Member Since: Jun 2004
Location: I tend to be leery of any guy who doesn't own a chainsaw or a handgun.
Posts: 18,350
Received 767 Likes
on
549 Posts
I can't perceive any lift or "steering getting light" issues on my '69. The current configuration is pretty simple, but have a couple additional tweaks planned. I've got the ride height down an inch or so from the stock height. I've got a Pace Car spoiler that helps divert a portion of the air from getting underneath the car, and I've blocked off the two grills (in front of the headlights) to reduce the volume of air entering the pre-radiator plenum. The car never overheats (I credit a good engine tune and a DeWitt radiator), even on 90* track days (like last week) or 100* track days (like last July). I may try to block off some of the center grill too.
I've been working on some aluminum panels to smooth the bottom of the car (particularly in the front before the air gets hopelessly turbulent) and other panels to help direct the air out the side gills instead of letting it collect under the car. Once I get this finished I need to do some wool tuft testing to see if it would be productive to lower the bottom edge of the underdoor rocker moldings. If it looks like air is actually trying to enter the underside of the car (from the sides) some of this air could be blocked by extending the molding lower edge downward. It looks like an additional two inch drop would be almost visually unnoticeable.
I've been working on some aluminum panels to smooth the bottom of the car (particularly in the front before the air gets hopelessly turbulent) and other panels to help direct the air out the side gills instead of letting it collect under the car. Once I get this finished I need to do some wool tuft testing to see if it would be productive to lower the bottom edge of the underdoor rocker moldings. If it looks like air is actually trying to enter the underside of the car (from the sides) some of this air could be blocked by extending the molding lower edge downward. It looks like an additional two inch drop would be almost visually unnoticeable.
Driver's side:
Depending on how things go at the next track day I might consider riveting a small vane on the bottom of each panel to direct some of the air under the panels outwards, again hopefully reducing the amount of air that tumbles around under the car.
I've also got the pattern cut out in cardboard for the horizontal "belly pan" that fits between the pacecar spoiler and the oilpan sump, but I haven't been able to get to the shop yet where I buy the larger sheets of aluminum (the panels above are just scrap pieces I had left over from previous projects). This belly pan should clean up some of the flow under the first few feet of the car.
#77
Burning Brakes
I like it, it'll be interesting to see if you notice any difference. It also looks like there are panels on the other side of the frame rails just forward of your new pieces. Looks like between the frame rails and the fenders. Is that also something you did? I don't recall those on other vettes...
#78
Tech Contributor
Member Since: Jun 2004
Location: I tend to be leery of any guy who doesn't own a chainsaw or a handgun.
Posts: 18,350
Received 767 Likes
on
549 Posts
I like it, it'll be interesting to see if you notice any difference. Thanks. I'm also looking around for a decent low pressure gauge to get an indication of the pressure levels on each side of the panels. It also looks like there are panels on the other side of the frame rails just forward of your new pieces. Looks like between the frame rails and the fenders. Is that also something you did? I don't recall those on other vettes...
#79
Pro
Its crazy how much air these cars pack under that tight little hood.I spent two years building and rebuilding a front and hood that would pass air through properly.I gained in cooling alot! and hood and front lift has all but dissappeared.I found that alot of the overheat/high heat problems with these cars has to do with venting more than drawing more in...It must be forced through the rad and released.I know that the high curves on the front fenders also create lift(This is why they were reduced from the macoII to the production vette.)So many ways to go and things to do to aid in the redution of lift. How much you want to do is up to you....
Still have a few changes for the lower front in the works.
Still have a few changes for the lower front in the works.
Last edited by SHOWME; 05-14-2012 at 07:42 PM.
#80
Tech Contributor
Member Since: Jun 2004
Location: I tend to be leery of any guy who doesn't own a chainsaw or a handgun.
Posts: 18,350
Received 767 Likes
on
549 Posts
Made a little progress today with the front undertray. It's 52" wide by 48" long, and the front edge is positioned under the pacecar spoiler. I still need to make a few more clearance cuts, but it looks like there's plenty of locations to make supporting hanger brackets.
I also recently bought a differential pressure gauge, so once I get the tray installed I'm interested in running some hoses from the gauge down to the front there to make some measurements.
I also recently bought a differential pressure gauge, so once I get the tray installed I'm interested in running some hoses from the gauge down to the front there to make some measurements.