!978 With Wiper Electrical Issues
#1
Advanced
Thread Starter
!978 With Wiper Electrical Issues
Hello all....the wipers on my 78 stopped working. I checked the fuse which appeared to be intact (see pic) but I changed it anyway, Worked for a few minutes then stopped again. Checked the fuse again. Again, not obviously blown but check out the other pic. The end of the fuse is taking a bit of abuse as you can see. I unplugged the 2 connections at the motor, cleaned em up good, replaced the same fuse, worked like a charm. Shut her down and cranked up again a few minutes later, no wipers...what is the most efficient way to troubleshoot this? Thanks in advance,
Dan
Dan
#2
Pro
Check the fuses with an ohmeter. Trust you have a multimeter. Sure looks like 2nd pic the fuse melted although at wrong spot. Usually they melt at the narrow spot in window as this is how they are designed. If you put the second one in while wiper motor was on with power you could do this maybe.
Anyway two thinks to check. First these fuse blocks can corrode where you install the fuse at each end. You can clean up each end where the fuse makes contact with a fiberglass pen or steel wool or fine emery. you can use spray contact cleaner. If it is good to start then use a meter on amp scale (30 amp) and see how much your wiper motor is drawing for current?
Anyway two thinks to check. First these fuse blocks can corrode where you install the fuse at each end. You can clean up each end where the fuse makes contact with a fiberglass pen or steel wool or fine emery. you can use spray contact cleaner. If it is good to start then use a meter on amp scale (30 amp) and see how much your wiper motor is drawing for current?
#3
Former Vendor
Member Since: Aug 2006
Location: Jeffersonville Indiana 812-288-7103
Posts: 76,656
Received 1,813 Likes
on
1,458 Posts
St. Jude Donor '08-'09-'10-'11-'12-'13-'14-'15
I'd start by cleaning the fuse connectors in the fuse box.... then see what happens. It's common for the terminals in the fuse box to become corroded and when this happens it creates resistance. So clean them.. it's not easy but you can glue sand paper to a small dowel and rub it in and out of the terminal until cleaned.
If this doesn't fix the issue there is a ton of info on my tech page. The link is listed below.
Willcox
https://willcoxcorvette.com/
http://repairs.willcoxcorvette.com/
If this doesn't fix the issue there is a ton of info on my tech page. The link is listed below.
Willcox
https://willcoxcorvette.com/
http://repairs.willcoxcorvette.com/
#4
Advanced
Thread Starter
Check the fuses with an ohmeter. Trust you have a multimeter. Sure looks like 2nd pic the fuse melted although at wrong spot. Usually they melt at the narrow spot in window as this is how they are designed. If you put the second one in while wiper motor was on with power you could do this maybe.
Anyway two thinks to check. First these fuse blocks can corrode where you install the fuse at each end. You can clean up each end where the fuse makes contact with a fiberglass pen or steel wool or fine emery. you can use spray contact cleaner. If it is good to start then use a meter on amp scale (30 amp) and see how much your wiper motor is drawing for current?
Anyway two thinks to check. First these fuse blocks can corrode where you install the fuse at each end. You can clean up each end where the fuse makes contact with a fiberglass pen or steel wool or fine emery. you can use spray contact cleaner. If it is good to start then use a meter on amp scale (30 amp) and see how much your wiper motor is drawing for current?
#5
Advanced
Thread Starter
Check the fuses with an ohmeter. Trust you have a multimeter. Sure looks like 2nd pic the fuse melted although at wrong spot. Usually they melt at the narrow spot in window as this is how they are designed. If you put the second one in while wiper motor was on with power you could do this maybe.
Anyway two thinks to check. First these fuse blocks can corrode where you install the fuse at each end. You can clean up each end where the fuse makes contact with a fiberglass pen or steel wool or fine emery. you can use spray contact cleaner. If it is good to start then use a meter on amp scale (30 amp) and see how much your wiper motor is drawing for current?
Anyway two thinks to check. First these fuse blocks can corrode where you install the fuse at each end. You can clean up each end where the fuse makes contact with a fiberglass pen or steel wool or fine emery. you can use spray contact cleaner. If it is good to start then use a meter on amp scale (30 amp) and see how much your wiper motor is drawing for current?
I'd start by cleaning the fuse connectors in the fuse box.... then see what happens. It's common for the terminals in the fuse box to become corroded and when this happens it creates resistance. So clean them.. it's not easy but you can glue sand paper to a small dowel and rub it in and out of the terminal until cleaned.
If this doesn't fix the issue there is a ton of info on my tech page. The link is listed below.
Willcox
https://willcoxcorvette.com/
http://repairs.willcoxcorvette.com/
If this doesn't fix the issue there is a ton of info on my tech page. The link is listed below.
Willcox
https://willcoxcorvette.com/
http://repairs.willcoxcorvette.com/
#6
Pro
Yes if only one speed use the Willcox website to bench test your wiper motor. These are old and the wiper switch is a terrible switch. Originals can be taken apart and cleaned up but rotten design. It can also be tested out of car. New ones from China intermittent too.
#7
Former Vendor
Member Since: Aug 2006
Location: Jeffersonville Indiana 812-288-7103
Posts: 76,656
Received 1,813 Likes
on
1,458 Posts
St. Jude Donor '08-'09-'10-'11-'12-'13-'14-'15
The imported switches are hit or miss with about 1 out of 10 being junk.
Here is how to rebuild the switch: http://repairs.willcoxcorvette.com/w...tch-repair.pdf
Here is how to test the switch once you get it out of the car.
If the car is in my shop I'll just rebuild the switch vs, selling a new one. And while it's hard to get the pot open, if you do decide to pull it apart just pay attention to how it came apart and don't drop the spring inside.
Willcox
https://willcoxcorvette.com/
http://repairs.willcoxcorvette.com/
Please bump our sale threads if you get a chance..