85 C4 Dyno Lethal Performance SA,TX
#1
Pro
Thread Starter
85 C4 Dyno Lethal Performance SA,TX
Well after 3 years of building this car and all the issues from the old TPI harness to going carb to EZ EFI it's finally done and ready to be put back together!!!
She made 306RWHP and 370lbTQ, the mods are ported 113 Heads, Weiand Street manifold, Hedman longtubes, Fitted to stock diameter 94 exhaust,X pipe in place of the resonator no Cats, and Maxflow mufflers(cheap) and ZF6 Swapped EZ EFI Vr1 swapped, Tuned by Lethal Performance.
She was an original 4+3 car and in not so fun condition when I got it, overall I was happy with the HP but upset I didn't get to 400lbtq I suppose I'll have to go Cam just nervous about the Vacuum with the EZ EFI I plan to drive it till it explodes then go with a Built 383
She made 306RWHP and 370lbTQ, the mods are ported 113 Heads, Weiand Street manifold, Hedman longtubes, Fitted to stock diameter 94 exhaust,X pipe in place of the resonator no Cats, and Maxflow mufflers(cheap) and ZF6 Swapped EZ EFI Vr1 swapped, Tuned by Lethal Performance.
She was an original 4+3 car and in not so fun condition when I got it, overall I was happy with the HP but upset I didn't get to 400lbtq I suppose I'll have to go Cam just nervous about the Vacuum with the EZ EFI I plan to drive it till it explodes then go with a Built 383
Last edited by L98Justin; 04-16-2017 at 09:04 AM.
#3
Pro
Thread Starter
I actually removed and traded that bumper to my parts dealer and went back to the early bumper since that's the only way my Morrison spoiler would look right
#5
Pro
Thread Starter
Unfortunately after driving for the last day or so we found we had a bad wideband 02 and it was dumping and pulling fuel it's back in the shop and being replaced, but damn it sure does pull hard I can't wait to have her back on Tuesday
#8
Safety Car
I was wondering about the wheels. I had no idea that people were making knock offs of the CCW wheels. Maybe John sold out at the right time.
The Original CCWs
Richard Newton
Compressed Air in Your Shop
The Original CCWs
Richard Newton
Compressed Air in Your Shop
Last edited by rfn026; 02-17-2017 at 10:03 AM.
The following users liked this post:
rfn026 (03-06-2017)
#11
Pro
Thread Starter
#12
Pro
Thread Starter
I didn't get a chance to take a picture with it installed but this is the new rear bumper and morrison spoiler together, bad picture I know but I had to hold the spoiler and bumper with one hand and take the picture with the other
Last edited by L98Justin; 02-18-2017 at 07:30 AM.
#15
Pro
Thread Starter
Finally got a call on the issues with my Corvette and the EZ EFI System; it runs great in open loop as soon as closed loop hits it dumps fuel they are re-tracing wiring but with TX2k here I won't hear anything new until Monday/tuesday... I'm losing a little faith in it but I refuse to go back to a Carb on this car... F.A.S.T seems to think that the interference is due to the wiring from the MSD Box to the Dizzy I hope they don't give up on it, but I've been looking into other shops in the SA area
#20
Pro
Thread Starter
Oh yea could be better though; and sadly no. I stopped by their shop today and they are still scratching their heads I keep telling them to get FAST involved.. I'm gonna end up with a new dizzy and external coil and a street fire ignition next week