FS: LT1 Turbo Kit, Anbody looking for a fun project?
#1
Melting Slicks
Thread Starter
FS: LT1 Turbo Kit, Anbody looking for a fun project?
I've tried selling my car as is, but I don't seem to be getting any serious interest. So I'm parting out my car. The turbo kit includes ALL exhaust piping(engine to exhaust tips), intake piping, intercooler, turbo, wastegate, BOV, radiator shrouds, oil feed and drain lines, custom 7qt oil pan, radiator hose modifications.
The car managed to go 12.5 @ 118mph when I had it on a stock setup with a cam. I managed a 2.X 60' on that run. Let the mph tell the story, and that was on 8psi, safe for a stock engine.
No cutting or drilling of the car is required to install this setup. You will have to modify the placement of your A/C or remove it if you prefer. And you will have to reroute your fuel lines.
Below is a picture of the kit installed. I'm looking to get $2750 + shipping for everything.
TURBO KIT:
1 3/4 “ Headers
2.5” cross over pipe Jet hot coated in black 2000 degree
3” into turbocharger - coated on 2000 degree jet hot
Turbonetics T-76 Ball Bearing turbo charger with .96 a/r (Newly Rebuilt this winter)
Turbonetics Racegate with black spring
3.5” down pipe – jet hot coated in 1500 degree sterling finish
y-connector to dual 2 ¾” pipes
through dual 3” pass through mufflers and out dual 3” rolled stainless steel tips
large IC in front of radiator
Intake piping all jet hot sterling coated
Tial 50mm BOV
7Qt oil pan with custom turbo fitting
Oil lines
I also will be selling my ACCEL DFI Gen 7 with wideband O2, distributor, and harness. This comes with the modified intake manifold in the picture. I will be asking $2300 for this setup, or $4500 for both.
The car managed to go 12.5 @ 118mph when I had it on a stock setup with a cam. I managed a 2.X 60' on that run. Let the mph tell the story, and that was on 8psi, safe for a stock engine.
No cutting or drilling of the car is required to install this setup. You will have to modify the placement of your A/C or remove it if you prefer. And you will have to reroute your fuel lines.
Below is a picture of the kit installed. I'm looking to get $2750 + shipping for everything.
TURBO KIT:
1 3/4 “ Headers
2.5” cross over pipe Jet hot coated in black 2000 degree
3” into turbocharger - coated on 2000 degree jet hot
Turbonetics T-76 Ball Bearing turbo charger with .96 a/r (Newly Rebuilt this winter)
Turbonetics Racegate with black spring
3.5” down pipe – jet hot coated in 1500 degree sterling finish
y-connector to dual 2 ¾” pipes
through dual 3” pass through mufflers and out dual 3” rolled stainless steel tips
large IC in front of radiator
Intake piping all jet hot sterling coated
Tial 50mm BOV
7Qt oil pan with custom turbo fitting
Oil lines
I also will be selling my ACCEL DFI Gen 7 with wideband O2, distributor, and harness. This comes with the modified intake manifold in the picture. I will be asking $2300 for this setup, or $4500 for both.
#3
Le Mans Master
Brian, I cant believe the deal you offered and no one purchased your car. Personally I think its a sign that the economy is in very bad shape and people are reluctant to spend any money that is unnecessary. Good luck with the sale of your turbo kit, but I do wish you would change your mind. You have been a great source of info on this forum!!
At any rate, here is a TTT for ya.
At any rate, here is a TTT for ya.
#5
Melting Slicks
Thread Starter
I think so too. Hopefully someone out there is looking for some big hp.
I would also be willing to throw in the extra fuel lines, custom polished fuel rails, 72# injectors, Aeromotive FPR, modified fuel rail covers, tank fittings, and a walbro 255 pump(secondary) for an extra $750. That's a 1,000 hp fuel system for pretty cheap.
I would also be willing to throw in the extra fuel lines, custom polished fuel rails, 72# injectors, Aeromotive FPR, modified fuel rail covers, tank fittings, and a walbro 255 pump(secondary) for an extra $750. That's a 1,000 hp fuel system for pretty cheap.
Last edited by mn_vette; 09-18-2008 at 02:22 PM.
#6
Melting Slicks
Thread Starter
No takers on $2750 for a turbo kit????
ebay buy it now prices:
T-76 Ball Bearing turbo 1400
Wastegate 400
Tial 50mm BOV 250
intercooler 500
That's 2550 for the main items.
So you're paying $200 for the entire intake and exhaust piping.
I can throw in a vortech FMU as well, so you are basically getting all the piping for free. All you have to do is pick up a BTM off of ebay and you are set to run boost on your LT1.
ebay buy it now prices:
T-76 Ball Bearing turbo 1400
Wastegate 400
Tial 50mm BOV 250
intercooler 500
That's 2550 for the main items.
So you're paying $200 for the entire intake and exhaust piping.
I can throw in a vortech FMU as well, so you are basically getting all the piping for free. All you have to do is pick up a BTM off of ebay and you are set to run boost on your LT1.
#8
I might be interested in the ECU and associated components. Let me see where my budget is and I will hit you back.
I would buy the whole system but my turbos already shipped.
I would buy the whole system but my turbos already shipped.
#9
Melting Slicks
Thread Starter
ttt, it looks like I may be buying a house and could use the extra cash on hand. Does nobody want a turbo vette? There's no way you could build this system for that price.