For Sale- C4 throttle cable clips
05-25-2016, 11:28 PM
#1
Advanced
Thread Starter
For Sale- C4 throttle cable clips
Are your accelerator clips broken/loose/missing on your 1991-1996 LT1 engine? These plastic clips replace part # 10054847 which has been discontinued by GM. After much research last year I found a suitable replacement that is pretty darn close, just have to trim two tabs with a razor knife.
After using them for a full year now I can give them two thumbs up!
I AM NOW COMPLETELY SOLD OUT....THANKS TO ALL THAT REPLIED!
Cheers!
Jonny
After using them for a full year now I can give them two thumbs up!
I AM NOW COMPLETELY SOLD OUT....THANKS TO ALL THAT REPLIED!
Cheers!
Jonny
Last edited by ZeeAreOne94; 05-27-2016 at 02:10 PM. Reason: Sold out
05-26-2016, 12:00 AM
#2
Melting Slicks
Are your accelerator clips broken/loose/missing on your 1991-1996 LT1 engine? These plastic clips replace part # 10054847 which has been discontinued by GM. After much research last year I found a suitable replacement that is pretty darn close, just have to trim two tabs with a razor knife.
After using them for a full year now I can give them two thumbs up! I have 18 pcs left that I do not need (I had to buy a minimum of 20 pcs) and am selling them in pairs for $1....hope that isn't asking too much. Unfortunately I cannot find a cheaper way to mail them other than small package postal rate at $2.45 ($3.45 total)....if someone knows of a much cheaper way please let me know!
Thx!
Jonny
After using them for a full year now I can give them two thumbs up! I have 18 pcs left that I do not need (I had to buy a minimum of 20 pcs) and am selling them in pairs for $1....hope that isn't asking too much. Unfortunately I cannot find a cheaper way to mail them other than small package postal rate at $2.45 ($3.45 total)....if someone knows of a much cheaper way please let me know!
Thx!
Jonny
Thanks,
Steve
The following users liked this post:
ZeeAreOne94 (05-28-2016)
The following users liked this post:
ZeeAreOne94 (05-27-2016)
The following users liked this post:
ZeeAreOne94 (05-28-2016)
The following users liked this post:
ZeeAreOne94 (05-28-2016)
The following users liked this post:
ZeeAreOne94 (05-28-2016)
05-27-2016, 02:07 PM
#11
Advanced
Thread Starter
Yes, but postal clerk laughed and said no way, it would not be "machinable"...dang clips are too thick.
Oh well, I'll set aside the last two sets for ya! PM sent.
WOW these went fast. Thanks to everyone who responded.
The following users liked this post:
Ron B C4 (06-01-2016)
05-31-2016, 06:33 PM
#15
Advanced
Thread Starter
05-31-2016, 06:36 PM
#16
Advanced
Thread Starter
The following users liked this post:
Fastnail (05-31-2016)
05-31-2016, 07:02 PM
#18
Advanced
Thread Starter
Got them on Ebay. Here's the link:
http://www.ebay.com/itm/361319957723
Note: you will have to trim two pcs of nylon at the base of the clip in order for them to sit flush.
Cheers!
Last edited by ZeeAreOne94; 05-31-2016 at 07:04 PM.
The following users liked this post:
Fastnail (05-31-2016)
05-31-2016, 10:05 PM
#19
Pro
OK, found it!
Got them on Ebay. Here's the link:
http://www.ebay.com/itm/361319957723
Note: you will have to trim two pcs of nylon at the base of the clip in order for them to sit flush.
Cheers!
Got them on Ebay. Here's the link:
http://www.ebay.com/itm/361319957723
Note: you will have to trim two pcs of nylon at the base of the clip in order for them to sit flush.
Cheers!
Cheers
