FS: 383 Engine Build Parts - Heads, Intake, Headers, Shortblock etc
#1
Tech Contributor
Thread Starter
383 Engine Build Parts - Heads, Intake, Headers, Shortblock etc
I am tearing down my 383 and parting it out to build a new engine. I will continue to drive the car until somebody buys something at which point I will tear the car down.
All prices are OBO. I will add pictures later. PM Me with any questions. I am open to separating items if I think I stand a decent chance of selling them individually.
FOR SALE:
HSR w/fuel rails and injectors, and Kirban Billet Regulator $900 (Fits under C4 Hood) 32 LB Bosch III Injectors
58mm Professional Products Throttle Body $125
TPIS Headers $300 - Ceramic Coating is pretty well worn off. Headers are wrapped with DEI Titanium Exhaust wrap. Have been that way since July.
Dart Pro 1 Aluminum Heads - Angle Plugs - $1000 - Ported, flow 280 CFM @.500. Includes springs good to .600 Lift (dual spring style) Titanium retainers
Rotating Assy $800 - Scat 9000 Crank, Scat 6" forged I-beam rods, SRP 5cc Flat Top Pistons .030 Over
Roller Rockers $80 - Skip White 1.6 RR.
Stud Girdle $80 - Never ran this it's been sitting in my garage for 3 years. Brand new
Fast Dual Sync Dizzy $250 - Needed to run timing if using a FAST System
MSD 6A $150
Billet AIR Pump Eliminator $80
Lokar Dipstick $25
GM 4 Bolt Block Clearanced for Stroker .030 Over $200
Comp Cams 280 XFI Roller Cam - $100
TFS Pushrods 7.300" - $50
GM Performance Lifters - $50
Professional Products Externally Balanced 6.75" SFI Approved Harmonic Balancer $100
FlowKooler Water Pump $50
March Power and Amp Series UnderDrive Pulleys $80
CS144 Alternator $80
Proform Crinkle Black Chevrolet Logo Valve Covers $50 PERIMETER BOLT
AC Compressor/Bracket - $50
Thanks for Looking!
Jeremy
All prices are OBO. I will add pictures later. PM Me with any questions. I am open to separating items if I think I stand a decent chance of selling them individually.
FOR SALE:
58mm Professional Products Throttle Body $125
TPIS Headers $300 - Ceramic Coating is pretty well worn off. Headers are wrapped with DEI Titanium Exhaust wrap. Have been that way since July.
Dart Pro 1 Aluminum Heads - Angle Plugs - $1000 - Ported, flow 280 CFM @.500. Includes springs good to .600 Lift (dual spring style) Titanium retainers
Rotating Assy $800 - Scat 9000 Crank, Scat 6" forged I-beam rods, SRP 5cc Flat Top Pistons .030 Over
Roller Rockers $80 - Skip White 1.6 RR.
Stud Girdle $80 - Never ran this it's been sitting in my garage for 3 years. Brand new
Fast Dual Sync Dizzy $250 - Needed to run timing if using a FAST System
MSD 6A $150
Lokar Dipstick $25
GM 4 Bolt Block Clearanced for Stroker .030 Over $200
Comp Cams 280 XFI Roller Cam - $100
TFS Pushrods 7.300" - $50
Professional Products Externally Balanced 6.75" SFI Approved Harmonic Balancer $100
FlowKooler Water Pump $50
March Power and Amp Series UnderDrive Pulleys $80
CS144 Alternator $80
Proform Crinkle Black Chevrolet Logo Valve Covers $50 PERIMETER BOLT
Thanks for Looking!
Jeremy
Last edited by Pwnage1337; 11-30-2018 at 08:10 PM.
#3
Tech Contributor
Thread Starter
I am pretty sure they are steel valves, 2.02 intake and 1.6 exhaust. I did not have new valves put in the heads from the time I purchased them. I know for sure they have titanium retainers and locks
#4
Heel & Toe
The following users liked this post:
Brian81CJ (09-10-2018)
The following users liked this post:
fast.asleep (10-08-2018)
#13
Tech Contributor
Thread Starter
Sale is pending on
HSR
Heads
Lifters
Stud Girdle
Rockers
Intake
Headers
AIR Pump Elim
HSR
Heads
Lifters
Stud Girdle
Rockers
Intake
Headers
AIR Pump Elim
Last edited by Pwnage1337; 10-04-2018 at 02:19 PM.
#18
Tech Contributor
Thread Starter
These items are still up for grabs since I haven't heard from the people who wanted them:
Under Drive Pulleys
Throttle Body
Valve Covers
Under Drive Pulleys
Throttle Body
Valve Covers