Notices
C4 Parts for Sale/Wanted C4 Corvette Performance Parts, Superchargers, Turbo Kits, Wheels & Tires, Exterior Enhancements, OEM, Aftermarket

FS: (2) lt engines

 
Old 12-30-2018, 06:28 PM
  #1  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default (2) lt engines

i have (2) lt engines for sale. whichever sells, i am keeping the other one to go in the 96.
the first one, which is still in the car, is an lt4 which has been rebuilt and has approx 200 miles and 1 dyno tune on it and runs. the rebuild consisted of block work: hot tanked and checked over, line honed the saddles, decked to 0, honed the cylinders as it didn't need to be bored. rods were resized, crank was polished, pistons were checked and cleaned, reciprocating assembly balanced. oil pan was dipped to clean all buildup or debris. lt4 heads were milled to flat and 3-angle valve job performed. springs were checked and shimmed to height. installed new crank, cam, rod bearings, rings and freeze plugs. arp main studs also installed. new oil pump and timing chain, accel cap and rotor, seals and gaskets.
engine consists of short block w/ gm hot cam ( .525/525 w/1.6 roller rockers ), lt4 heads and intake manifold, lt4 valve covers, throttle body, harmonic balancer w/pully, oil pan and stock exhaust manifolds if you want them. with the gm hot cam and 1 5/8" headers this engine made 362 rwhp and 357 rwtq until about 4700 rpm's we started getting ignition problems, we thought. after we got back to the hotel from the dyno tune, i started hearing 'that knock' which sounded like a rod so we towed it back home and it sat in the garage as i was going to drop in the 383 that has been setting on the engine stand until about a week ago. i was in the process of pulling the rack out and removing the balancer, the bolts were loose and the balancer just fell off. i guess the vibration from the balancer was being picked up by the knock sensors and retarding the timing. so bolted the balancer back in and started it up, no vibrations, no knocking. there is oil in the pan and coolant in the block so i was able to run it for a minute or so and took some videos of it, but it seems they will not upload. if interested, e-mail me and i will send them to you. asking $3000.00 plus shipping and paypal fees if used.
please dis-regard all the blue tape with writing, they are my way of identifying where things need to go upon putting back together.




_ _


_ _


_ _


_ _

the second engine is an lt1 383 cid short block. this engine has all new components, short block has been assembled and lives its life on an engine stand.
block was tanked and inspected, align bored mains with arp main studs, cylinders were bored .030 over and honed w/plates, decked to 9.00, relieved for 3.75 stroke.
all new crank, rod, cam bearings, freeze plugs, arp main studs
crank shaft is a new callies dragonslayer 3.750 stroke for 383 cid.
rods are a set of 6.0 childs and alberts that i had on a storage shelf, checked and resized.
pistons are wiseco forged for 11.0 to 1 compression
assembly was balanced
cloyes true roller timing set
crower 00562 cam, NT/EXH - Dur @ .050 Lift: 221/230 RR: 1.5/1.5 Gross Lift: .525/.545 LSA: 114 RPM: 1500 to 5800 Redline: 6300
canton 15-240t oil pan & pickup
melling m155hv high volume oil pump
short block will come with a 94 ( early style ) timing cover
asking $2500 for short block, oil pan and front cover.



_ _

_ _

_ _

if the short block sells, then i will have a pair of afr 195 heads and a lt4 intake manifold to sell. i purchased these from forum member tpi_421_vette after he massaged them and the flow numbers are very good.
thank ya'll for looking.
Sleazy Rider is offline  
Old 12-30-2018, 11:21 PM
  #2  
jayjones
CF Member
 
Member Since: Mar 2018
Location: Indiana
Posts: 64
Thanks: 0
Thanked 13 Times in 7 Posts
Default

Where are the engines located (ziocode)
jayjones is online now  
Old 12-31-2018, 12:40 AM
  #3  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

Conroe Texas, 77385
Sleazy Rider is offline  
Old 12-31-2018, 08:13 PM
  #4  
BLKMAMBA
CF Senior Member
 
Member Since: Jan 2017
Location: West Deptford New Jersey
Posts: 356
Thanked 10 Times in 10 Posts
Default

what would be the price on the 195's? and those are really good #'s for a hotcam
BLKMAMBA is offline  
Old 12-31-2018, 08:51 PM
  #5  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

Originally Posted by BLKMAMBA View Post
what would be the price on the 195's? and those are really good #'s for a hotcam
looking to get $2500 for the heads and intake as a package as they were port matched to each other, that's what i have in them. already taking a bath on the short block.
Sleazy Rider is offline  
Old 01-06-2019, 09:01 AM
  #6  
BLKMAMBA
CF Senior Member
 
Member Since: Jan 2017
Location: West Deptford New Jersey
Posts: 356
Thanked 10 Times in 10 Posts
Default

Originally Posted by Sleazy Rider View Post
i have (2) lt engines for sale. whichever sells, i am keeping the other one to go in the 96.
the first one, which is still in the car, is an lt4 which has been rebuilt and has approx 200 miles and 1 dyno tune on it and runs. the rebuild consisted of block work: hot tanked and checked over, line honed the saddles, decked to 0, honed the cylinders as it didn't need to be bored. rods were resized, crank was polished, pistons were checked and cleaned, reciprocating assembly balanced. oil pan was dipped to clean all buildup or debris. lt4 heads were milled to flat and 3-angle valve job performed. springs were checked and shimmed to height. installed new crank, cam, rod bearings, rings and freeze plugs. arp main studs also installed. new oil pump and timing chain, accel cap and rotor, seals and gaskets.
engine consists of short block w/ gm hot cam ( .525/525 w/1.6 roller rockers ), lt4 heads and intake manifold, lt4 valve covers, throttle body, harmonic balancer w/pully, oil pan and stock exhaust manifolds if you want them. with the gm hot cam and 1 5/8" headers this engine made 362 rwhp and 357 rwtq until about 4700 rpm's we started getting ignition problems, we thought. after we got back to the hotel from the dyno tune, i started hearing 'that knock' which sounded like a rod so we towed it back home and it sat in the garage as i was going to drop in the 383 that has been setting on the engine stand until about a week ago. i was in the process of pulling the rack out and removing the balancer, the bolts were loose and the balancer just fell off. i guess the vibration from the balancer was being picked up by the knock sensors and retarding the timing. so bolted the balancer back in and started it up, no vibrations, no knocking. there is oil in the pan and coolant in the block so i was able to run it for a minute or so and took some videos of it, but it seems they will not upload. if interested, e-mail me and i will send them to you. asking $3000.00 plus shipping and paypal fees if used.
please dis-regard all the blue tape with writing, they are my way of identifying where things need to go upon putting back together.




_ _


_ _


_ _


_ _

the second engine is an lt1 383 cid short block. this engine has all new components, short block has been assembled and lives its life on an engine stand.
block was tanked and inspected, align bored mains with arp main studs, cylinders were bored .030 over and honed w/plates, decked to 9.00, relieved for 3.75 stroke.
all new crank, rod, cam bearings, freeze plugs, arp main studs
crank shaft is a new callies dragonslayer 3.750 stroke for 383 cid.
rods are a set of 6.0 childs and alberts that i had on a storage shelf, checked and resized.
pistons are wiseco forged for 11.0 to 1 compression
assembly was balanced
cloyes true roller timing set
crower 00562 cam, NT/EXH - Dur @ .050 Lift: 221/230 RR: 1.5/1.5 Gross Lift: .525/.545 LSA: 114 RPM: 1500 to 5800 Redline: 6300
canton 15-240t oil pan & pickup
melling m155hv high volume oil pump
short block will come with a 94 ( early style ) timing cover
asking $2500 for short block, oil pan and front cover.



_ _

_ _

_ _

if the short block sells, then i will have a pair of afr 195 heads and a lt4 intake manifold to sell. i purchased these from forum member tpi_421_vette after he massaged them and the flow numbers are very good.
thank ya'll for looking.
Are the headers fs?
BLKMAMBA is offline  
Old 01-06-2019, 03:52 PM
  #7  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

Originally Posted by BLKMAMBA View Post
Are the headers fs?
headers are for sale. they are stainless works 1 5/8" that have been jet hot coated and cats that mate up to a corsa cat-back.
Sleazy Rider is offline  
Old 01-06-2019, 03:59 PM
  #8  
BLKMAMBA
CF Senior Member
 
Member Since: Jan 2017
Location: West Deptford New Jersey
Posts: 356
Thanked 10 Times in 10 Posts
Default

Sounds expensive. I'm afraid to ask
BLKMAMBA is offline  
Old 01-06-2019, 04:32 PM
  #9  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

Originally Posted by BLKMAMBA View Post
Sounds expensive.
thinking $1,000 shipped conus. about 1/2 of what i paid for the set.
Sleazy Rider is offline  
Old 01-07-2019, 07:52 AM
  #10  
migander
Junior Member
 
Member Since: Mar 2011
Posts: 16
Thanks: 0
Thanked 0 Times in 0 Posts
Default

On the short-block is it internal balance front and rear or standard balance?
Standard balance being internal front external rear.
migander is offline  
Old 01-07-2019, 12:18 PM
  #11  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

Originally Posted by migander View Post
On the short-block is it internal balance front and rear or standard balance?
it is standard balance so you can use whatever flywheel/clutch combination you want and have it balanced separately before installation.
Sleazy Rider is offline  
Old 01-07-2019, 02:09 PM
  #12  
migander
Junior Member
 
Member Since: Mar 2011
Posts: 16
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Originally Posted by Sleazy Rider View Post
it is standard balance so you can use whatever flywheel/clutch combination you want and have it balanced separately before installation.
"Standard" crankshaft balance on an LT1/LT4 is internal front and external rear. Rear is balanced via the flywheel.
This means if you want to change flywheel or clutch after the fact the new flywheel/clutch assembly must be match balanced to whatever combination is being removed.

Maybe I should have asked if the rotating assembly is "neutral" balanced meaning one can use any combination of flywheel and clutch as long as the flywheel and clutch are "0"/"neutral" balance.
migander is offline  
Old 01-07-2019, 03:31 PM
  #13  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

i guess it is 'neutral balanced'. i can take whatever flywheel/clutch assy to him and he will ' 0 balance ' it. then when i install it on the crank, everything will be balanced.
i hope this makes sense.
Sleazy Rider is offline  
Old 01-21-2019, 12:58 AM
  #14  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

new week, another round
Sleazy Rider is offline  
Old 01-21-2019, 07:04 PM
  #15  
jayjones
CF Member
 
Member Since: Mar 2018
Location: Indiana
Posts: 64
Thanks: 0
Thanked 13 Times in 7 Posts
Default

I would come get that short block from you if it was closer to Indiana
jayjones is online now  
Old 01-21-2019, 09:54 PM
  #16  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

Originally Posted by jayjones View Post
I would come get that short block from you if it was closer to Indiana
been hanging around too long. i will pay the freight.
Sleazy Rider is offline  
Old 01-22-2019, 09:13 AM
  #17  
jayjones
CF Member
 
Member Since: Mar 2018
Location: Indiana
Posts: 64
Thanks: 0
Thanked 13 Times in 7 Posts
Default

Sending PM
jayjones is online now  
Old 01-22-2019, 12:21 PM
  #18  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

Originally Posted by jayjones View Post
Sending PM
replied
Sleazy Rider is offline  
Old 02-08-2019, 05:16 PM
  #19  
Sleazy Rider
CF Senior Member
Thread Starter
 
Sleazy Rider's Avatar
 
Member Since: Sep 2004
Location: Conroe Texas
Posts: 3,959
Thanks: 0
Thanked 26 Times in 25 Posts
Default

lets go,go,go
Sleazy Rider is offline  
 


Thread Tools
Search this Thread
Quick Reply: FS: (2) lt engines


Sponsored Ads
Vendor Directory

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.