Do you need an OptiSpark?
#1
Supporting Vendor
Thread Starter
Do you need an OptiSpark?
Restore spark to your LT1/LT4 motor with this BRAND NEW Distributor from AIP Electronics
This Distributor EXCEEDS OEM specification and comes 100% complete with everything needed including a new Optispark wiring harness.
(Note: Harness may not fit all applications and you may have to use your original harness.) Our AIP LT1 Optical Encoder is temp rated at 330°
and produces an accurate timing reference signal up to 8000 RPM, exceeding the OEM Mitsubishi encoder used in the AC Delco factory LT1 distributors.
This is most likely the best aftermarket LT1/LT4 distributor you will ever come across. Uses AIP's own Mitsubishi Specification Optical Encoder
for the most accurate/dependable LT1 Distributor yet.
We have negotiated with AIP and starting 12/01/2015 AIP Optisparks purchased through SacCityCorvette come with a 2 Year Replacement Warranty!
Must be purchased through SacCityCorvette to receive this 2 yr warranty!
Newly updated Vented $189.95
Non Vented $180.95
http://www.saccitycorvette.com/AIPOptiSpark.html
Here's whats new for the Vented Opti!
Revised Upper and Lower Rubber Gaskets with increased sealing surface
-Thread Lock Compound pre-applied to rotor and sensor mounting screws
-Coated EMI Shield
-Revised Laser Cut Shutter Disc for improved timing accuracy
-Revised Mitsubishi-Spec optical sensor
-Precision Japanese Ball Bearing
Photos of the new updated Vented AIP Optispark (cap colors vary)
NON VENTED OPTI
Non Vented Sensor
This Distributor EXCEEDS OEM specification and comes 100% complete with everything needed including a new Optispark wiring harness.
(Note: Harness may not fit all applications and you may have to use your original harness.) Our AIP LT1 Optical Encoder is temp rated at 330°
and produces an accurate timing reference signal up to 8000 RPM, exceeding the OEM Mitsubishi encoder used in the AC Delco factory LT1 distributors.
This is most likely the best aftermarket LT1/LT4 distributor you will ever come across. Uses AIP's own Mitsubishi Specification Optical Encoder
for the most accurate/dependable LT1 Distributor yet.
We have negotiated with AIP and starting 12/01/2015 AIP Optisparks purchased through SacCityCorvette come with a 2 Year Replacement Warranty!
Must be purchased through SacCityCorvette to receive this 2 yr warranty!
Newly updated Vented $189.95
Non Vented $180.95
http://www.saccitycorvette.com/AIPOptiSpark.html
Here's whats new for the Vented Opti!
Revised Upper and Lower Rubber Gaskets with increased sealing surface
-Thread Lock Compound pre-applied to rotor and sensor mounting screws
-Coated EMI Shield
-Revised Laser Cut Shutter Disc for improved timing accuracy
-Revised Mitsubishi-Spec optical sensor
-Precision Japanese Ball Bearing
Photos of the new updated Vented AIP Optispark (cap colors vary)
NON VENTED OPTI
Non Vented Sensor
__________________
Don't forget to check out our products at www.saccitycorvette.com
If you like our products, tell others! If not, tell us!
Don't forget to check out our products at www.saccitycorvette.com
If you like our products, tell others! If not, tell us!
Last edited by SacCityCorvette; 11-10-2019 at 10:32 PM.
#3
Supporting Vendor
Thread Starter
#8
Supporting Vendor
Thread Starter
#9
Pro
#10
Supporting Vendor
Thread Starter
Christian
SacCityCorvette
#12
Supporting Vendor
Thread Starter
#15
Supporting Vendor
Thread Starter
Hi kimmer,
You most likely will need a Non Vented Opti for a 92. It does come with a harness but there is a possibility that wont fit. There are a few oddball harness's out there. If the harness doesn't fit you can use your original one or modify the new one. We had a 97 z28 that the harness didn't fit and we had to trim a little of the plastic out to get it to plug in. Its the only one we came across but one of our customer had the same issue. Its rare but it happens. Just a heads up.
Thanks
Christian
You most likely will need a Non Vented Opti for a 92. It does come with a harness but there is a possibility that wont fit. There are a few oddball harness's out there. If the harness doesn't fit you can use your original one or modify the new one. We had a 97 z28 that the harness didn't fit and we had to trim a little of the plastic out to get it to plug in. Its the only one we came across but one of our customer had the same issue. Its rare but it happens. Just a heads up.
Thanks
Christian
#16
#17
We have Fangs, Alignit Tools,Big 3, Coolits,Optisparks Please check our Website http://www.saccitycorvette.com/index.html
#19
Supporting Vendor
Thread Starter
We are not boasting, just letting people know about AIP's warranty.
Just on a side note, the MSD only has a 1 year on their $500 Opti.
Thanks
Christian
The following users liked this post:
klandry5 (04-24-2019)
#20
Supporting Vendor
Thread Starter
Hi seabright,
I agree, a extended warranty would be a good idea and would give customers more confidence to buy their Opti's. I will run that by them.
Thank you for your input!
Christian
I agree, a extended warranty would be a good idea and would give customers more confidence to buy their Opti's. I will run that by them.
Thank you for your input!
Christian