1985 4+3 OD Sluggish
#62
Melting Slicks
1 piece is external to the oil pan with a seal housing bolted to the back. 2 piece is internal mounted in the rear main cap. Need to remove oil pan, oil pump etc. Tons of fun especially with no hoist.
The following users liked this post:
Bfenty (02-18-2018)
#64
Le Mans Master
whoops I was thinking 1 piece as well. My bad. Though it's just a lot of time on your back, the pan, oil pump and cap should clear. Mine dropped right out. I wouldn't do it unless it wash showing signs though.
#66
Le Mans Master
I mean it could be burning off on the clutch...
#69
Le Mans Master
After this last month I'm under the impression that oil pretty much goes everywhere when it leaks.
#70
Melting Slicks
I mean if it's getting into the bell housing it's going to end up there eventually no? Unless I'm missing something. It was more of a joke/spit ball than a real assessment. I've heard of it happening. Not on a c4 in particular but it could. Usually it ends up in a slipping clutch though.
After this last month I'm under the impression that oil pretty much goes everywhere when it leaks.
After this last month I'm under the impression that oil pretty much goes everywhere when it leaks.
#71
Le Mans Master
So I am not understanding your logic. I don't see how you think it can get to the friction side of the flywheel. Leaking out the engine seal, oil is going to run down the back of the engine block correct? It then escapes to the exterior. If by some fluke some oil were to make it to the backside of the flywheel, the centrifugal force would sling it to the side of the bellhousing, again to escape to the exterior. We are talking seepage here not a gusher. Please elaborate on your hypothesis.
I said it just to be that guy (anything is better than nothing sometimes.) I really don't believe this is what's happening. I'm sorry man. Didn't mean to mislead anyone. I've seen some weird things happen. So anything that comes to mind I end up saying. Usually I end up being the jerk too. Again, sorry...
#72
Drifting
Thread Starter
Member Since: Mar 2017
Location: Nashville TN
Posts: 1,897
Received 164 Likes
on
136 Posts
2017 C4 of Year Finalist
Well, I’ll throw it out there that my clutch has a weird habit of juddering when I start and shift in 1st/2nd. Not sure what causes that. It doesn’t make the car undrivable but it can be annoying
#73
Le Mans Master
I don't know how yours behaves exactly but mine has a sort of two step when you clutch. You get the initial bite and then you think okay I'm starting to roll then you get this secondary jump when it bites in again. When I drive the 55 I just sort of ease into the clutch with a little bit of rpms. On the vette you have to pump it a little otherwise it'll just buck. I have no clue on the history of my clutch or what kind is in it. All I know is the pedal is amount the most on off clutches I've ever driven. The engagement is right there...
#74
Melting Slicks
No, you're 100% correct. If it were a quart in a couple hundred miles then maybe. I'm visualizing it as the engine is spinning and the seep is being flung by the output shaft and Kind of misting in the bellhousing just causing a constant fine spray if you will. The stop and go is allowing that fine spray to sort of be like a misting coating, like spraying wd. I really doubt it's the case but anything is possible. Each time you clutch you get a little of it on it. Most ends up vaporized and leaves. Some stays. If I spray water on my rims and go for a quick drive it'll all pretty much fling off. If I spray tire shine and go for a quick drive I'll have runs and droplets. The viscosity and shear also play a role. Granted the tire is spinning at significantly less revolutions per minute than the flywheel is but the same theory applies as long as the mass balances and force balances check out.
I said it just to be that guy (anything is better than nothing sometimes.) I really don't believe this is what's happening. I'm sorry man. Didn't mean to mislead anyone. I've seen some weird things happen. So anything that comes to mind I end up saying. Usually I end up being the jerk too. Again, sorry...
I said it just to be that guy (anything is better than nothing sometimes.) I really don't believe this is what's happening. I'm sorry man. Didn't mean to mislead anyone. I've seen some weird things happen. So anything that comes to mind I end up saying. Usually I end up being the jerk too. Again, sorry...
You are not being a jerk in my mind. I just don't think you fully understand the interior workings and are just throwing some **** at the wall to see if some sticks. No problem, you more or less said so.
In any case, I think there is a better chance of my aunt growing a ******* and becoming my uncle than there is of a main seal weep contaminating a friction surface on the flywheel.
#75
Drifting
Thread Starter
Member Since: Mar 2017
Location: Nashville TN
Posts: 1,897
Received 164 Likes
on
136 Posts
2017 C4 of Year Finalist
I don't know how yours behaves exactly but mine has a sort of two step when you clutch. You get the initial bite and then you think okay I'm starting to roll then you get this secondary jump when it bites in again. When I drive the 55 I just sort of ease into the clutch with a little bit of rpms. On the vette you have to pump it a little otherwise it'll just buck. I have no clue on the history of my clutch or what kind is in it. All I know is the pedal is amount the most on off clutches I've ever driven. The engagement is right there...
My original ‘85 (now my parts car) had the stiffest clutch I’ve ever felt-it bit and bit HARD. I think it must have been an upgraded racing clutch or something because the previous owner had been turning it into a drag car. It had other problems but the clutch/OD weren’t one.
#76
Drifting
Thread Starter
Member Since: Mar 2017
Location: Nashville TN
Posts: 1,897
Received 164 Likes
on
136 Posts
2017 C4 of Year Finalist
I'm starting a new thread to ask for help on dropping the transmission. I figured this thread has wandered enough that it's probably time to start a new one HERE.