Birdman

2001 Corvette Z06
-$31,000
-Charleston, SC

BODY/LOOKS:

-48k miles on body/interior, 14k miles on build
-Clear title
-Kenne Bell cowl hood with holes cut to vent trapped air at high speeds
-All lights have been tinted using PPG paint/clear
-5% window tint on sides and rear
-Front license plate screen to allow better airflow
-HID lights
-Stubby antenna


ENGINE:

-6.0 LQ9. Bored/Stroked to 408ci, aprox 9.2:1 compression(14k miles MAX on EVERY engine part)
-Full eagle rotating assembly with Weisco Pistons
-All clevite bearings. Complete ARP studded. Hellfire ring set
-PRC LS3 heads with further work done
-Cam specs are 244/249 .643 .643 114+4
-Melling high volume oil pump
-DeWitts low profile radiator
-Polished and smoothed metal aluminum valve covers
-Relocated/hidden (inside front fenders) MSD coil packs
-Dual catch can system with AN lines and fittings
-Rotella T6 oil


FORCED INDUCTION

-A&A Vortech YSi @ 17lbs
-2.85" A&A upper pulley
-10% Innovaters West crank pulley
-Dallas Performance Flip Drive. Still have the 8rib pulley on alternator
-Custom polished aluminum 4" blower inlet
-Polished Aluminum 3 1/2" intercooler to Throttle body tube
-LS2 TB
-LS3 intake
-ECS intercooler setup with waste gate boost control (runs 137mph on low boost about 10 psi and 150 on high boost 17psi pump gas)
-Procharger "bigred" blowoff valve
-Extra supercharger belt included (never had one break or fly off, just good to keep a spare)
-Extra (new) A&A 2.65 pulley should you want to up the boost a tad


FUEL SYSTEM:

-Aftermarket pumps in tank (forgot what brand)
-A&A secondary boost reference fuel system (kicks on around 3-5 lbs of boost) Hobbs switch
-Bosch 044 secondary pump (will include an extra one)
-83lb injectors (Deka Siemans)
-Holley fuel rails
-Holley fuel pressure regulator (-10 I/O, -8 return)
-Alky Control Meth kit, dual nozzle, windshield washer tank used


EXHAUST:

-1 7/8 American Racing long tubes
-Magnaflow Performance inline mufflers/resonaters integrated to the x-pipe
-Custom over-axle and out the sides (dual) 4" exhaust tips
-Not obnoxiously loud at idle or cruise, can hold normal conversation. or if you get tired of said conversation, just floor it.
-Monkey Fab powder coated trim rings


DRIVETRAIN:

-Mantic 9000 twin-disk semi-metallic clutch
-TR6060 transmission and C6Z diff with fresh Redline fluids in both
-RKT diff mounts
-Rebuilt torque tube from an 03Z, new Timken bearings, new Tick slave cylinder, Poly coupler in front and billet coupler in rear, new AC Delco pilot bearing
-Tick remote clutch bleeder
-MGW Gen 3 short throw shifter with base
-Black with red striped shift ****


SUSPENSION:

-Pfadt BOA coilovers
-Pfadt front and rear sway bars
-Adjustable Pfadt end links


BRAKES:

-Hawk HPS pads
-D/S rotors
-Included are a pair of stainless steel brake lines (not installed)


INTERIOR:

-Mod red
-Triple gauge pod with: Haltech dual wideband, fuel pressure, and boost/vacuum (light up red, white, and blue! Murica!)
-6pt Bolt in roll bar with removable door bars
-All Bluish/white color LED lighting
-Custom radio bezel with 7" touch screen/navi/DVD player
-NGK NTK AFX A/F gauge in console (yes, 3 total with a 4th 02 sensor not being used and tucked away underneath)
-5pt Harness on drivers seat
-Sound system: Focal ($700 each!) door speakers, Focal subwoofer, Amp
-Insulated partition divider which cuts down on rear road and exhaust noise
-Raptor shift light
-Sound deadening insulation on top of torque tube tunnel (under console)
-Second auxillary switch on console free to connect whatever
-Lloyds deluxe floor mats
-Red/black leather console cover

WHEELS/TIRES:

-Stock C5Z Alcoa wheels
-Weld S71 rear wheels, 17x10.5 with MT ET Street R, 305/45/17

Misc:

-Haltech Elite 2500 with traction control, launch control, no lift shift + more, can tune and customize on your laptop with free software and access!
-Line lock with switch on console
-I can possibly throw in my 11" Alienware gaming laptop with the Haltech tuning software already on it
-Tuned by Mark Rios #RiosRacing near Fayetteville, NC.
-Mounted fire extinguisher on roll cage

Car has made 900rwhp and has ran a 9.7 @ 150 with a 1.7 60'.

I'm only selling because I want to get into a 69 Corvette resto-mod/pro-touring project.

Birdman

Birdman

Bump?

Birdman

Back up

x88

Nice car, wouldn't the massive torque cause rubbing issues with such tight clearance in the exhaust exit area?

Vetteman Jack

What is your price - $37K or $31K? Please PM me a response and I can adjust the main title if needed. Thanks.