Kenne Bell High Rise Hood (We have 2 in stock) CHEAP!!
#1
Melting Slicks
Thread Starter
Member Since: Apr 2009
Location: Las Vegas Nevada
Posts: 2,203
Likes: 0
Received 2 Likes
on
2 Posts
St. Jude Donor '12
Kenne Bell High Rise Hood (We have 2 in stock) CHEAP!!
Hey All,
Recently, we picked up our shipment of KB Blowers and Hoods. But we decided to gab a few extra hoods since alot of you guys like to run them with other setups.
They are all brand new, and in the box ready for shipping.
They will work with any supercharger or turbo kit on the market. They also work with most high rise N/A manifolds.
These hoods are made of fiberglass, and have a smooth finished surface on both the top and botttom.
People who see these hoods in person, absolutely love them. Although their a very aggressive hood, with about 3-3.5" of raised cowl, they still retain a very factory look. So it doesnt look like you have some top fuel hood on your sleek car.
Their not for everyone, but the people who like this type of hood, LOVE THEM...
We only have 2 available at this price, so they should go pretty fast.
789.00 SHIPPED TO YOUR DOOR!!!
This is an amazing price, since shipping usually runs $150.00-200.00 via truck freight.
If your local to us, or you have your own freight company, we will let you pick one up for $649.00
Here are a few pictures of our Orange car with this hood. If you look on the forum, you'll see a few other colors.
Recently, we picked up our shipment of KB Blowers and Hoods. But we decided to gab a few extra hoods since alot of you guys like to run them with other setups.
They are all brand new, and in the box ready for shipping.
They will work with any supercharger or turbo kit on the market. They also work with most high rise N/A manifolds.
These hoods are made of fiberglass, and have a smooth finished surface on both the top and botttom.
People who see these hoods in person, absolutely love them. Although their a very aggressive hood, with about 3-3.5" of raised cowl, they still retain a very factory look. So it doesnt look like you have some top fuel hood on your sleek car.
Their not for everyone, but the people who like this type of hood, LOVE THEM...
We only have 2 available at this price, so they should go pretty fast.
789.00 SHIPPED TO YOUR DOOR!!!
This is an amazing price, since shipping usually runs $150.00-200.00 via truck freight.
If your local to us, or you have your own freight company, we will let you pick one up for $649.00
Here are a few pictures of our Orange car with this hood. If you look on the forum, you'll see a few other colors.
The following users liked this post:
CorvetteBrent (09-05-2018)
#4
Drifting
Member Since: Sep 2008
Location: somewhere shooting my assault rifles
Posts: 1,389
Likes: 0
Received 3 Likes
on
3 Posts
Hey can you take a shot of the underside of the hood and the back view of the rear cowl area? It looks like in the picture the rear cowl is closed off or one solid back and not opened up to engine compartment?
#5
Drifting
The rear of the hood is closed off. There is a support that runs across the back of the hood. It is built like a box frame design.
There have been a few posts where people have cut three holes through that support to allow heat to escape. In one post the holes were covered with a similar screen as the front brake vents, for a nice finished look.
I had toyed with the idea of maybe mounting my boost/fuel pressure gauges in that spot......
The following users liked this post:
CorvetteBrent (09-05-2018)
#6
Hattitude, was it you that had a shot of the hood from the driver's seat? That gives a really good idea of how high the hood actually sits.
Nice hood - great price! Two guys are going to get lucky
Nice hood - great price! Two guys are going to get lucky
#7
Drifting
#8
Le Mans Master
wow. so my last post is invalid - this is my new favorite hood!
i, too, would like to see a shot from inside & would also like to know if this will cover a Maggie TVS2300 without trimming. thanks
i, too, would like to see a shot from inside & would also like to know if this will cover a Maggie TVS2300 without trimming. thanks
The following users liked this post:
CorvetteBrent (09-05-2018)
#11
Le Mans Master
i just happened to come across this thread again & figured i'd help out if anybody needs it...
this hood (whether or not they'll still sell it at this price anymore) will, in fact, clear a TVS2300 without modification. i just got mine put on yesterday
this hood (whether or not they'll still sell it at this price anymore) will, in fact, clear a TVS2300 without modification. i just got mine put on yesterday
The following users liked this post:
CorvetteBrent (09-05-2018)
#14
I actually have one of these...got alot of compliments and "where did you get that from" comments aswell...only thing done might not like is the fact you cannot see the pass headlight from inside making it hard to see when going over blind hills.and this hood is remarkably heavy so do not doubt its strength.
The following users liked this post:
CorvetteBrent (09-05-2018)
#15
Le Mans Master
i've had mine on since June & i love it. i've had so many compliments on it. just to be honest, it did take a bit of glassing to line everything up right, but it's the same with most hoods.
here's the best inside shot i have right now
and a new outside shot from the other day
here's the best inside shot i have right now
and a new outside shot from the other day
Last edited by _zebra; 10-04-2011 at 07:53 PM.
The following users liked this post:
CorvetteBrent (09-05-2018)
#17
Le Mans Master