Auto Swap Thread
#523
Intermediate
Well some parts came in today and its about time to get it back together. Auto swap in my 01 Z06.
Level VII RPM 4L65/70E transmission, with billet input, billet
pump rotor, and billet 300M output shaft, SFI Bellhousing, deep
pan, Transbrake
DSS 3.5 in. Driveshaft
DSS Urethane couplers
Corvette SFI flexplate
Cone for Auto flexplate assembly
Coan Converter
Shifter assembly and shifter cable
Auto Torque Tube
PCS TCM-2000 controller and wiring harness
Im posting this for people thinking of doing the swap and for yall to double check my work, make sure i do everything right.
Lets get started
car all torn apart
New Tranny
Flexplate
Lots of wiring
PCS Tranny Controller
Level VII RPM 4L65/70E transmission, with billet input, billet
pump rotor, and billet 300M output shaft, SFI Bellhousing, deep
pan, Transbrake
DSS 3.5 in. Driveshaft
DSS Urethane couplers
Corvette SFI flexplate
Cone for Auto flexplate assembly
Coan Converter
Shifter assembly and shifter cable
Auto Torque Tube
PCS TCM-2000 controller and wiring harness
Im posting this for people thinking of doing the swap and for yall to double check my work, make sure i do everything right.
Lets get started
car all torn apart
New Tranny
Flexplate
Lots of wiring
PCS Tranny Controller
I have a couple questions about the swap. If you could give me a call or text @209-269-9543. Please
#524
Racer
mind if i hijack and get some info about my auto swap???
i finished mine about 2-3 months ago... went with a 00 auto tranny harness (according to the guy i bought it from) (my car is a 2000)connected to an rpm jumper harness... and a reflash on my computer(well im under the impression it was reflash to an auto). the car drives good and shifts really good, but the car will not shift at high rpms. im not sure if its at a certain rpm that it wont shift or at WOT if wont shift. seems that i can go 1/4-1/2-3/4 throttle and it will shift nice and firm but at wot it just bangs off the rev limiter. i was told that the cars computer is not telling the transmission to shift according to the scanner when plugged into the car. i would appreciate any help or leads to figure this out.. my tuner says its not in the tune and that he has tried everything he can think of to get it to shift.. was told that i can get the tci controller and that would for sure work but i know its been down with a factory auto harness and rpm jumper harness and ive already spent the money on that route so i would like to make it work... please help.
thanks and sorry for the high jack, bad *** parts being used for sure, im jealous.
i finished mine about 2-3 months ago... went with a 00 auto tranny harness (according to the guy i bought it from) (my car is a 2000)connected to an rpm jumper harness... and a reflash on my computer(well im under the impression it was reflash to an auto). the car drives good and shifts really good, but the car will not shift at high rpms. im not sure if its at a certain rpm that it wont shift or at WOT if wont shift. seems that i can go 1/4-1/2-3/4 throttle and it will shift nice and firm but at wot it just bangs off the rev limiter. i was told that the cars computer is not telling the transmission to shift according to the scanner when plugged into the car. i would appreciate any help or leads to figure this out.. my tuner says its not in the tune and that he has tried everything he can think of to get it to shift.. was told that i can get the tci controller and that would for sure work but i know its been down with a factory auto harness and rpm jumper harness and ive already spent the money on that route so i would like to make it work... please help.
thanks and sorry for the high jack, bad *** parts being used for sure, im jealous.
#526
This is such an awesome thread. Ive read thru several times, but still unsure on a few things.
I am amassing all of the parts for my auto swap for my SC Z06, ~650 rwhp. So far I have the following:
Harness/shifter
built 4L60e
converter drive plate
auto torque tube housing with stock auto driveshaft
transmission cooler
stock bellhousing (not using)
flexplate with hub, clamp and bolt
Here are the parts that I still need to acquire:
stall
torque tube input and output shafts OR built TT
SFI bellhousing
output shaft seal and oring
shift cable mounting bracket
Questions:
How much HP will the stock auto driveshaft hold?
Do I still need a conversion harness from RPM with the stock harness?
Are the manual TT input and output shafts the same as an auto (can i rob parts from my manual TT?)
Is this the differential seal plate? I may already have it:
I am amassing all of the parts for my auto swap for my SC Z06, ~650 rwhp. So far I have the following:
Harness/shifter
built 4L60e
converter drive plate
auto torque tube housing with stock auto driveshaft
transmission cooler
stock bellhousing (not using)
flexplate with hub, clamp and bolt
Here are the parts that I still need to acquire:
stall
torque tube input and output shafts OR built TT
SFI bellhousing
output shaft seal and oring
shift cable mounting bracket
Questions:
How much HP will the stock auto driveshaft hold?
Do I still need a conversion harness from RPM with the stock harness?
Are the manual TT input and output shafts the same as an auto (can i rob parts from my manual TT?)
Is this the differential seal plate? I may already have it:
Last edited by TX Z06 02; 02-26-2017 at 09:39 AM.
#527
AMP Racing
Member Since: Aug 2006
Location: Washington TWP NJ
Posts: 10,446
Received 466 Likes
on
352 Posts
2023 C5 of the Year Finalist - Modified
2017 C5 of Year Finalist
St. Jude Donor '09-'10-'11-'12
Questions:
How much HP will the stock auto driveshaft hold?
Do I still need a conversion harness from RPM with the stock harness?
Are the manual TT input and output shafts the same as an auto (can i rob parts from my manual TT?)
Is this the differential seal plate? I may already have it:
How much HP will the stock auto driveshaft hold?
Do I still need a conversion harness from RPM with the stock harness?
Are the manual TT input and output shafts the same as an auto (can i rob parts from my manual TT?)
Is this the differential seal plate? I may already have it:
2) Yes - you need the harness that has about 16 wires that you will have to insert into the PCM. RPM and other places can make this for you.
3) No - get an Auto TT
4) Yes - that is the plate you need.
You will likely have to make a bracket to hold the shift cable, as the oem part is no longer available.
Have fun with your project!
#528
Race Director
I doubt the stock TT bushings will take much more than the stock output before failing. I would look into getting some aftermarket couplings. The mechanics are rather simple, however the wiring can take a bit of time if you want to get everything working. You can save yourself some headaches and use an after-market shift controller and avoid the whole re-wiring process.
#529
Ok, so I talked to Shane at RPM today and got some things figured out.
One thing I am concerned with is that the harness that I have is from a 2000 (12189826) and my Z06 is a 2002. Will this harness work, or do I need a 2002 harness?
One thing I am concerned with is that the harness that I have is from a 2000 (12189826) and my Z06 is a 2002. Will this harness work, or do I need a 2002 harness?
#530
AMP Racing
Member Since: Aug 2006
Location: Washington TWP NJ
Posts: 10,446
Received 466 Likes
on
352 Posts
2023 C5 of the Year Finalist - Modified
2017 C5 of Year Finalist
St. Jude Donor '09-'10-'11-'12
Do you have the service manual for your 02Z? You will be able to reference the harness to your manual to ensure the pins are correct.
IIRC, I put a harness from a 99 into my 01Z.
IIRC, I put a harness from a 99 into my 01Z.
#531
#532
AMP Racing
Member Since: Aug 2006
Location: Washington TWP NJ
Posts: 10,446
Received 466 Likes
on
352 Posts
2023 C5 of the Year Finalist - Modified
2017 C5 of Year Finalist
St. Jude Donor '09-'10-'11-'12
You will really want one of those. I suggest you pick it up before proceeding with your swap.
#533
#534
AMP Racing
Member Since: Aug 2006
Location: Washington TWP NJ
Posts: 10,446
Received 466 Likes
on
352 Posts
2023 C5 of the Year Finalist - Modified
2017 C5 of Year Finalist
St. Jude Donor '09-'10-'11-'12
Gene Culley can get you the OEM service manuals. They are really helpful.
Cultrag Performance. Vendor on here.
Cultrag Performance. Vendor on here.
#535
Race Director
Hi Bill,
Sorry I haven't got an email out to yet. The transmission harnesses are different between the years. In mid 2001 they changed over some of the connectors.
If you look at the harness that you took out should see some dates on the harness. You want to find one in an automatic in the general time frame.
I'll try and send some more info tonight.
Sorry I haven't got an email out to yet. The transmission harnesses are different between the years. In mid 2001 they changed over some of the connectors.
If you look at the harness that you took out should see some dates on the harness. You want to find one in an automatic in the general time frame.
I'll try and send some more info tonight.
#536
Ok, I purchased some service manuals. Havent dove into them yet.
I have my entire drivetrain, pedals, etc out of the car. bellhousing was a @#$%#$@!
Fenders are off. The only thing that I havent removed is the manual wiring harness. Looks like it splits and goes to either side of the engine, I assume the passenger side goes to the EBCM. Where are the plugs? How hard is this to remove?
I have my entire drivetrain, pedals, etc out of the car. bellhousing was a @#$%#$@!
Fenders are off. The only thing that I havent removed is the manual wiring harness. Looks like it splits and goes to either side of the engine, I assume the passenger side goes to the EBCM. Where are the plugs? How hard is this to remove?
#537
AMP Racing
Member Since: Aug 2006
Location: Washington TWP NJ
Posts: 10,446
Received 466 Likes
on
352 Posts
2023 C5 of the Year Finalist - Modified
2017 C5 of Year Finalist
St. Jude Donor '09-'10-'11-'12
You shouldn't have to remove the harness going to the ebcm. (Iirc)
Just remove the harness that runs down inside the tunnel.
Take your time and it'll come to you. It's not that difficult.
Just remove the harness that runs down inside the tunnel.
Take your time and it'll come to you. It's not that difficult.
#538
Ordered my rpm harness yesterday and making a trade for all of the other auto stuff I needed this weekend.
#539
H.V. checking in,
what is this a belated april fools joke?
V
H.V.
what is this a belated april fools joke?
V
H.V.