Not one thing its another. Problem with my new YSI
#1
Melting Slicks
Thread Starter
Not one thing its another. Problem with my new YSI
Called vortech but they were already closed. Hopefully they will make it right.
#3
Team Owner
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
ttt
Dam buddy hate to hear that in the car. Sucks when a man does all that work on a new part every thing set just so so then you hear that from under the hood. I am sure you will send it in they will look at it & will do right by it.. Robert
#4
Le Mans Master
Man that's don't sound good. What happened did it starve for oil or belt too tight or over spin. Could just be a bad batch of China bearings. Good luck I hope all goes well
#6
Melting Slicks
Thread Starter
this is a brand new unit on initial start up. no oil starvation and hasnt been overspun. just a bad unit i guess. ill call them in a bit and keep you guys posted.
#8
Melting Slicks
Thread Starter
#11
sorry to hear that
U should of purchased a 2200r
U should of purchased a 2200r
Last edited by blown81bu; 10-30-2015 at 12:03 PM.
#12
Drifting
Sorry to see & hear that. Hopefully they'll provide you with decent support. What balancer and S/C pulley sizes were you running?
Seriously? If we don't run what you have, then we have junk? Come on.
Well, we'll run my YSI against your 2200R soon enough
Seriously? If we don't run what you have, then we have junk? Come on.
Well, we'll run my YSI against your 2200R soon enough
#13
Melting Slicks
Thread Starter
Paul, I have bit my lip for a long time now but seriously STFU. No one asked you. Dave, its a 8"/2.85" combo. Called Vortech and no warranty. Looks like I'm out $750 for new bearings unless the guy I bought it from decides to go half.
EDIT: Looks like they are going to work with me.
EDIT: Looks like they are going to work with me.
Last edited by algZO6; 10-30-2015 at 03:57 PM.
#14
Melting Slicks
Thread Starter
#15
Premium Supporting Vendor
Member Since: Oct 2004
Location: Providing the most proven supercharger kits for your C5/6/7 609-752-0321
Posts: 23,315
Received 1,085 Likes
on
656 Posts
Paul, I have bit my lip for a long time now but seriously STFU. No one asked you. Dave, its a 8"/2.85" combo. Called Vortech and no warranty. Looks like I'm out $750 for new bearings unless the guy I bought it from decides to go half.
EDIT: Looks like they are going to work with me.
EDIT: Looks like they are going to work with me.
Was it used?
#16
Melting Slicks
Thread Starter
#18
Team Owner
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
Albert looks like getting it done still under the way it was they should stand behind it for you.. They are some nice guys out at that shop...
#19
Paul, I have bit my lip for a long time now but seriously STFU. No one asked you. Dave, its a 8"/2.85" combo. Called Vortech and no warranty. Looks like I'm out $750 for new bearings unless the guy I bought it from decides to go half.
EDIT: Looks like they are going to work with me.
EDIT: Looks like they are going to work with me.
If your still 4l60 I wish u luck. .don't last long with our kinda power..
2..85 8". Nice combo
Last edited by blown81bu; 10-30-2015 at 09:44 PM.
#20
ISIS SUCKS FAT CHOAD
Paul, I have bit my lip for a long time now but seriously STFU. No one asked you. Dave, its a 8"/2.85" combo. Called Vortech and no warranty. Looks like I'm out $750 for new bearings unless the guy I bought it from decides to go half.
EDIT: Looks like they are going to work with me.
EDIT: Looks like they are going to work with me.
On another note, I was going to tell you that you could certainly open the case up yourself and put bearings in it. I think there are places that offer replacement bearings; but it looks like they are taking care of you.