BLOWNBLUEZ06 Built - 2004 Supercharged Commemorative Edition(z16) Corvette z06
#41
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
/\ when I first saw your car over there I made a joke about buying his daughter a vette... not sure if you have seen her car but the paint scheme is VERY similar lol
#43
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
lol, just a joke
#44
Supporting Vendor
Thanks for the post. I hope you enjoy it! I was very pleased to see it make the power and while there are never any guarantees of reliability, I am confident you'll be able to enjoy this setup for a long time. I've tuned a lot of F/I C5's and have a good handful of them making more power than this one for years without issue. I am a big advocate of running either E85 or meth when making this kind of power and that was discussed but declined.
#46
Just wanted to give thanks to Blownbluez06 for helping me put together and tuning the perfect combo for this car.
I had a good idea of what I wanted and he helped me finalize everything down to every nut and bolt, including purchasing the A&A kit from him for my car.
He was very knowledgeable and was always willing to help and got the car done in a very timely manner.
The car turned out better than I could have imagined and drives like a dream.
If anyone is thinking about going supercharged, shoot him a message first.
Originally, I was shooting for 600rwhp, but the car ended up making 768/655 on 12lbs of boost with 93 octane alone.
Mods:
A&A Black Ti Trim v3 supercharger kit(4.0 pulley)
BTR Stage 2 cam
BTR .660 springs and Pushrods
Smith Brother’s Trunnion Rocker bushing kit
160 Degree Thermostat
Top Speed Headers with high flow cats and X-pipe
Innovator’s West 10% overdrive pulley
Corsa Xtreme Exhaust w/4” pro series tips
GM LS7 Clutch kit
New GM flywheel along with Slave Cylinder and remote bleeder kit
ECS stage 1 Fuel system(AEM 380lph pump)
I had a good idea of what I wanted and he helped me finalize everything down to every nut and bolt, including purchasing the A&A kit from him for my car.
He was very knowledgeable and was always willing to help and got the car done in a very timely manner.
The car turned out better than I could have imagined and drives like a dream.
If anyone is thinking about going supercharged, shoot him a message first.
Originally, I was shooting for 600rwhp, but the car ended up making 768/655 on 12lbs of boost with 93 octane alone.
Mods:
A&A Black Ti Trim v3 supercharger kit(4.0 pulley)
BTR Stage 2 cam
BTR .660 springs and Pushrods
Smith Brother’s Trunnion Rocker bushing kit
160 Degree Thermostat
Top Speed Headers with high flow cats and X-pipe
Innovator’s West 10% overdrive pulley
Corsa Xtreme Exhaust w/4” pro series tips
GM LS7 Clutch kit
New GM flywheel along with Slave Cylinder and remote bleeder kit
ECS stage 1 Fuel system(AEM 380lph pump)
#47
That blown CE is amazing. I have a 2004 CE Z06 Z16 and was afraid to mod it last year. This year I'm going more for show than go. At 63 my thirst for more power is satisfied with what I have. When I bought it ayear ago it already had a Vararam Intake, headers, x-pipe, no cats. I should get it dynoed to see if it is a tad higher than stock.
#48
Melting Slicks
Beautiful car! What is your timing set at with the 93 octane and 12lbs of boost?
#49
Man that's well done. Looks like a factory option.