Installed a HUD
#1
Instructor
Thread Starter
Member Since: Nov 2012
Location: Honolulu Hawaii
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
Installed a HUD
Just wanted to say thank you to those members who post "how to" here. I've installed the HUD today and the forum made the process simple. Now off to the next mod.
#2
Burning Brakes
I've purchased a HUD for my car but haven't installed it yet. Which instruction instructions did you follow? How long did it take? Any advise before I tackle this project?
#3
Instructor
Thread Starter
Member Since: Nov 2012
Location: Honolulu Hawaii
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
http://forums.corvetteforum.com/c5-t...d-install.html
Just take your time, especially when cutting the dash. I was able to use a cordless drill for drilling the projector holes. I didn't use sealant for the bezel. Ended up using flat washers and screws from the underside to secure it. The bezel has four posts that are ready for screws.
Took me about two hours. I took it apart earlier and also painted the console a radio trim for the dash.
#4
Administrator
Member Since: Mar 2001
Location: In a parallel universe. Currently own 2014 Stingray Coupe.
Posts: 342,933
Received 19,293 Likes
on
13,966 Posts
C7 of the Year - Modified Finalist 2021
MO Events Coordinator
St. Jude Co-Organizer
St. Jude Donor '03-'04-'05-'06-'07-'08-'09-'10-'11-'12-'13-'14-'15-'16-'17-'18-'19-
'20-'21-'22-'23-'24
NCM Sinkhole Donor
CI 5, 8 & 11 Veteran
Congrats on the install - you're right that this place has some great DIY instructions for members to follow.
So, what is the next mod?
So, what is the next mod?
#5
Instructor
Thread Starter
Member Since: Nov 2012
Location: Honolulu Hawaii
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
Not really a mod but fixing two remaining issues. Next week I replace the steering wheel sensor and then replace the headlight gears with brass gears. I'm getting the dreaded grindning noise when I turn them off.
#6
Team Owner
By Johnsos30
Don't show the wife when you take the dash out!
I've purchased a HUD for my car but haven't installed it yet. Which instruction instructions did you follow? How long did it take? Any advise before I tackle this project?
Don't show the wife when you take the dash out!
#7
Race Director
Member Since: Mar 2006
Location: Everywhere and Nowhere at all
Posts: 15,357
Received 1,679 Likes
on
1,135 Posts
2hrs!! Hell it took me two days!!! Well worth the tme,effort.
#8
Team Owner
Member Since: Mar 2004
Location: Oklahoma City OK
Posts: 58,259
Received 1,675 Likes
on
1,298 Posts
C6 of Year Finalist (appearance mods) 2019
Best mod that I ever did for sure!
#10
Instructor
Thread Starter
Member Since: Nov 2012
Location: Honolulu Hawaii
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
#11
Instructor
#12
Instructor
Thread Starter
Member Since: Nov 2012
Location: Honolulu Hawaii
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
#14
Race Director
It might me a good idea to check the HUD circuit board component solder joints before installing. I suspect that the same issue that causes our outside temperature display to dim and go out, causes the HUD display to eventially do the same when the ambient temps get up past 75.
My HUD is fine in the Winter but fades during the afternnon heat in Summer. Cracked component solder joints are the likely culprits.
My HUD is fine in the Winter but fades during the afternnon heat in Summer. Cracked component solder joints are the likely culprits.
#17
Instructor
Thread Starter
Member Since: Nov 2012
Location: Honolulu Hawaii
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
Well tonight I took it for a drive and noticed a couple of the buttons on the right side not lit up. Looks like the bulb may be bad so I'll remove it to fix this. While I'm at it I think I'll do the silver ring mod to the gauges. Who sells these?
#18
Intermediate
Hud
I want to also install a HUD in my 98. But would I have to replace the windshield as well? I was told if the car was not equipped with HUD then the factory windshield would not work, and also would I have to replace my stock cluster?
#20
Instructor
Thread Starter
Member Since: Nov 2012
Location: Honolulu Hawaii
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
No issues with the standard windshield. You are only seeing the reflection from the glass. The projector doesn't shoot the image onto the glass.