Anti-Venom 6 Speed Shifter Modification (Procedure)
#281
Instructor
Guys:
This modification will reduce the "notch" feeling when shifting between gears.
And allows for a more easy shift.
Its a MUST do for when you install a Short Shifter.
Easy to install and remove if you don't like it.
On my web site at the bottom:
http://ToqueZ06.com/
Anti-Venom 6 Speed Shifter Modification:
Toque
This modification will reduce the "notch" feeling when shifting between gears.
And allows for a more easy shift.
Its a MUST do for when you install a Short Shifter.
Easy to install and remove if you don't like it.
On my web site at the bottom:
http://ToqueZ06.com/
Anti-Venom 6 Speed Shifter Modification:
Toque
#282
Drifting
#283
Tech Contributor
Thread Starter
I never had anyone ask me though. Its a good question !
It should work in or out of gear I would think.
But as he said above... Neutral would likely be best.
Good luck !
Toque
#285
Tech Contributor
Thread Starter
#288
Instructor
Just did this mod today while installing my Corsa Xtreme. IT IS AWESOME. It made my MGW so much easier to manuever. Sure, not quite as notchy, but feels infinitely better. Just used one washer and don't plan on changing that.
The following users liked this post:
chasboy (03-11-2016)
#289
Le Mans Master
Member Since: Jul 2011
Location: Morristown New Jersey
Posts: 7,263
Received 914 Likes
on
721 Posts
Oldtimer
Hey Mark! I'm back! FULLY back Monday when I pick up my new '02 coupe!
As for the this thread, the anti venom reduces the pressure of the spring that holds the linkage in place in a particular gear. My moving the ball further 'out' it exerts less pressure. I did it on my Z, with the stock shifter and it works great. I think I used 1 spacer. I also took 1 3/4 out of my shift handle, making it a shorter shifter. I was very happy with the results.
As for the this thread, the anti venom reduces the pressure of the spring that holds the linkage in place in a particular gear. My moving the ball further 'out' it exerts less pressure. I did it on my Z, with the stock shifter and it works great. I think I used 1 spacer. I also took 1 3/4 out of my shift handle, making it a shorter shifter. I was very happy with the results.
#291
Instructor
https://www.corvetteforum.com/forums...od-washer.html
20 mm copper drain plug washer ( on another thread >>>>3/4" ID brass washer approx 1/16" thick )
I went to the big rig truck center and bought what I needed.
20 mm copper drain plug washer ( on another thread >>>>3/4" ID brass washer approx 1/16" thick )
I went to the big rig truck center and bought what I needed.
Last edited by 98C5P; 05-02-2017 at 01:28 PM.
#292
http://a.co/aQMLM1S
Gasket Thickness (mm): 1.25 mm
Inside Diameter (in): 0.807 In.
Outside Diameter (In): 1.071 In.
Gasket Thickness (mm): 1.25 mm
Inside Diameter (in): 0.807 In.
Outside Diameter (In): 1.071 In.
#293
Instructor
Wow, this seems like a cool/easy/cheap mod to do. I have the MGW short shifter and like how it has the shorter throw, but just a bit to "notchy" for me.
I plan on doing this soon and I'll check back with the results.
On a side note....by doing this mod, will it hurt anything in the transmission or clutch related?
I plan on doing this soon and I'll check back with the results.
On a side note....by doing this mod, will it hurt anything in the transmission or clutch related?
#294
Instructor
Wow, this seems like a cool/easy/cheap mod to do. I have the MGW short shifter and like how it has the shorter throw, but just a bit to "notchy" for me.
I plan on doing this soon and I'll check back with the results.
On a side note....by doing this mod, will it hurt anything in the transmission or clutch related?
I plan on doing this soon and I'll check back with the results.
On a side note....by doing this mod, will it hurt anything in the transmission or clutch related?
Only potential downside is a slightly higher possibly of the transmission popping out of gear... I have had this done for 2 years and have not come out of gear one single time.
#295
Instructor
Wow, this seems like a cool/easy/cheap mod to do. I have the MGW short shifter and like how it has the shorter throw, but just a bit to "notchy" for me.
I plan on doing this soon and I'll check back with the results.
On a side note....by doing this mod, will it hurt anything in the transmission or clutch related?
I plan on doing this soon and I'll check back with the results.
On a side note....by doing this mod, will it hurt anything in the transmission or clutch related?
I have found through trial and error, that a heavier shift **** makes it that much smoother !
do not use the white hurst ball junk, it's just that, and rattles ....
enjoy!
#297
Advanced
To those who have done this mod - is there any reason Not to use a 20mm aluminum crush washer instead of brass? I already have a ton of those laying around. Thanks.
#298
Tech Contributor
Thread Starter
#300
Tech Contributor
Thread Starter